Anycubic Photon Printer Owners 造訪社團

原文網址 Trung Mi
2020-01-11 12:15:55

excuse me. Normally when do you know it's time to change your FEP film?
I have just run the resin exposure file and the chart is clear on 1,2 and 9-10 column but "flat" in the center (4~7 coumn)
there for my conclusion is the FEP film is loose/ old
Is that right ?

翻譯年糕

原文網址 Dallas Visagie
2020-01-11 11:29:42

Well, I have been having some weird problems with my printer as of late. I will print the same file back to back and one will turn out completely fine and the other will fail spectacularly. I am printing with Elegoo Grey with a layer height of 0.05mm with an exposure time of 12s. I also make sure all the islands are supported by using the photon file validator. I have been having great results with these settings when the print doesn't have any failures. Any help would be appreciated.

翻譯年糕

Chris Wolfe
2020-01-11 11:32:25

Dallas Visagie
2020-01-11 11:34:51

Chris Wolfe
2020-01-11 11:35:42

Jarin Udom
2020-01-11 11:50:29

Tyron Craft
2020-01-11 11:52:14

Dallas Visagie
2020-01-11 11:59:13

Jarin Udom
2020-01-11 12:00:15

Dallas Visagie
2020-01-11 12:05:31

Jarin Udom
2020-01-11 12:06:18

Dallas Visagie
2020-01-11 12:08:28

Jarin Udom
2020-01-11 12:10:14

Dallas Visagie
2020-01-11 12:11:40

Matt Hooton
2020-01-11 15:36:48

Nat Sinclair
2020-01-12 05:35:19

原文網址 Aaron McCommon
2020-01-11 11:19:11

Any reason my writing a file is being so slow and corrupted? Saving to the harddrive. Latest chitubox i believe.

翻譯年糕

Zachary Ford
2020-01-11 11:29:57

原文網址 Jeremiah Chetwood
2020-01-11 10:32:24

Getting ready for assembly

翻譯年糕

Jeff Surma Jr.
2020-01-11 10:38:09

Shawn Barnes
2020-01-11 10:43:19

Jeff Surma Jr.
2020-01-11 10:48:48

Steve Haynes
2020-01-11 11:08:47

Jeremiah Chetwood
2020-01-11 11:56:19

Vorawich Watthanarojanaporn
2020-01-11 16:57:36

Roy Escherich
2020-01-11 17:08:06

Óttar Freyr Einarsson
2020-01-11 19:06:28

Vorawich Watthanarojanaporn
2020-01-11 19:14:22

Kevin A Thompson
2020-01-11 23:15:19

原文網址 Evan Kwong
2020-01-11 10:23:00

Carbon filter Merv rating?

I want to reduce odor pumped into the atmosphere. Does carbon filters help with this? What Merv rating would I need? I have a chart for what merv rating needed and their chemicals. However, I have trouble finding what chemicals are in the "ELEGOO standard grey photopolymer Resin for LCD" Elegoo does not state any chemicals they use. Formlabs shows what their resin uses, but people claim to barely smell it. I assume formlabs uses a different ingredient all together.

翻譯年糕

David Minford
2020-01-11 10:24:13

Evan Kwong
2020-01-11 10:26:27

Lamont Cutler
2020-01-11 10:27:55

Jarin Udom
2020-01-11 10:31:05

Jim Nelson
2020-01-11 10:36:55

原文網址 Brendan Wood
2020-01-11 09:58:48

Does anyone have a recommendation for a heating solution to keep the printer warm? It's a balmy 7.2C in the garage and I think it's the reason my prints are failing.

I've seen a make-your-own magnetic heater with assembly required, but I'd prefer just getting something off Amazon over having to order and put together multiple parts (if at all possible).

翻譯年糕

John Chrapkowski
2020-01-11 10:05:59

John Chrapkowski
2020-01-11 10:06:12

Matthew Overbeck
2020-01-11 23:32:09

原文網址 Ryan Shelvik
2020-01-11 09:57:08

Hey guys. I've had a few successful small minis print out...and trying something bigger now. I tiled him back, and want to hollow him out. I'm planning on giving Chitubox a shot with the hollowing feature, but not sure how thick I should make the walls, and looking for any other advice as I get this bad boy prepped.

翻譯年糕

Kris Leon
2020-01-11 10:00:32

Ryan Shelvik
2020-01-11 10:04:18

Kris Leon
2020-01-11 10:04:40

Mourni Tenchou
2020-01-11 10:22:26

Jarin Udom
2020-01-11 10:22:40

Victoria L. Cordone
2020-01-11 11:12:45

原文網址 Jake Ives
2020-01-11 09:54:30

So I ran a print last night, and it seems that halfway through, the bed shifted, and it started printing crooked. Is there a way to ensure the bed doesn’t move? It is a rather large and heavy print, could that have caused the issue?

翻譯年糕

Chris Wolfe
2020-01-11 10:02:43

Stefan Giudici
2020-01-11 10:22:30

原文網址 Adrian Półtorak
2020-01-11 09:38:52

Hi everyone!
I'm trying to get rid of some AA problems (mostly horizontal steps, gradient exposure controll), described here: https://www.alexwhittemore.com/efficacy-of-antialiasing-on-msla-prints/
I have made allready my own slicer who theoretically adresses those issues (it's in 3dsmax, very slow, but it works ;) Just need to create photon files from rendered images to make some tests. So, I'm looking now for a tool, where you can make photon file from series of images, but it needs to support grayscale images with AA . Anybody could help? :)
I also upgraded my photon (zrail and screen on the glass) to get the best quality possible and test the results under microscope, and share the results with you. 翻譯年糕