管理員
統計數據
原文網址 曹锐樑 2018-10-31 11:23:31
I have an atom 2.5 ex 3d printer and started printing dual filaments. I'm having a problem that it keeps clogging up everytime midprint. Do you know why that is? Below is a picture of what the filament looks like at the hot end when I've taken it out. Its does this all the time. Any help would be much appreciated, thanks
曹锐樑 2018-10-31 11:27:45
I have used simplify 3d settings as previously linked here: https://drive.google.com/....../1hV......
John Wachowski 2018-10-31 11:48:19
What filaments are you using? Is it just two different color PLAs?
阿童 2018-10-31 14:40:10
Check you PTFE tube length？ Try follow the step: https://atom3dp.squarespace.com/extruder-issue-en#yjunction
廖新弘 2018-10-31 14:44:11
你的管子沒有突出結合器，所以回抽時軟化PLA就卡住在噴頭固定螺絲與結合器之間
Fabio Hasseck 2018-10-31 16:34:18
What filaments, what temperature and printing speed? Also what slicer are you using?
曹锐樑 2018-11-01 02:18:07
Yes just 2 different colour PLA at 200C
曹锐樑 2018-11-01 02:21:33
Both PLA, 200deg C, print speed is 40mm/s and slicer is simplify 3D, I've been trying to use the latest cura but havent got the settings to work nicely
John Wachowski 2018-11-01 02:24:12
Feeding fresh filament, do both sides of your junction insert and retract without issue? Do this manually. It should slide in and out without binding or obstruction.
Birk Binnard 2018-11-01 03:00:44
You identified the problem yourself when you said "It does this every time." That is exactly what I encountered. From what I can tell the jams result from the fact that melted filament has a viscosity that always leaves a fine trail of filament behind when it is retracted. Over time this builds up and clogs the nozzle. The only way I could reliably fix this was to completely disassemble the nozzle and burn out the clog with a propane torch. I think the only way to reliable do multi-filament printing is with one nozzle for each filament. There was a guy named Jensen Huang working on this - but he seems to have disappeared. Here is his FB page: https://www.facebook.com/groups/150457119076159/
Fabio Hasseck 2018-11-01 03:22:12
Did you set Simplify to pull up to 120 m"m when switching filaments? also what is the retract speed?
曹锐樑 2018-11-01 05:33:57
120mm @ 40mm/s
曹锐樑 2018-11-01 05:36:18
I've got it as smooth as I can, I've pushed the PTFE tubes from the hot end and from the feed together and now going to try it now
曹锐樑 2018-11-01 06:08:20
I have checked the PTFE tube length and it is 35.5mm as per spec. We were given PTFE lube when we got our printer, when did we need to use that?
John Wachowski 2018-11-01 06:27:36
You are seeing the stringing. So there could be an issue with that too.
曹锐樑 2018-11-01 06:37:22
does that mean i should try print at a lower temp? have you got yours to work with dual printing? Im trying to print the tree frog
John Wachowski 2018-11-01 07:13:01
I haven't messed with it, but maybe 190C might get you where you need to be. Or a longer retraction distance/speed might snap it free.
原文網址 Joe Abaquin Bing Aquino 2018-10-19 08:03:59
Problem with my extruder gear.
It seems that it keep clogging my extruder gear and when printing, it stops extruding filaments and my print outs come nothing. Any suggestions? Or should I get a new gear.
Thanks for any response.
Tempo Casper 2018-10-19 08:13:30
Gear look good
阿童 2018-10-19 08:46:38
We recommend you change new one. Please sent the mail to info@atom3dp.com .
Joe Abaquin Bing Aquino 2018-10-19 09:40:55
Will post and video if I see any faulty at the hot end. Thanks guys
葉世瑋 2018-10-19 09:45:35
Do you hear the sound "click, "click", "click" when nothing comes out from extruder?
Joe Abaquin Bing Aquino 2018-10-22 02:33:23
I check the extruder and find nothing wrong but the only thing I needed was the gear. The sales expert noticed that it was worn out badly and I will need to go with a metal gear. Plus I found out that the PLA filaments (1kg) was not good (defect) and it was a soft filaments. The gear was eating it (clogging) and not pushing out more to the nozzle.
Cherub Shiao 2018-11-01 07:04:32
the right side gear will be fine, if still can't fix the clogging problem, change more soft spring
原文網址 SonicSy Yu 2018-09-17 23:53:08
剛入手了atom2.5ex，前天才組裝完成，昨天用官方的測試檔印出來的都很正常，今天試著印千年鷹結果變成這樣，想問一下各位前輩為何會發生這種狀況……？
施百鴻 2018-09-18 00:01:06
請附上設定參數 這樣大家比較好給建議
林似諭 2018-09-18 00:03:26
若是測試檔 沒問題，那就不用多說了，參數設定的問題！
SonicSy Yu 2018-09-18 00:10:10
我是用cura的推薦設定，層高0.2 填充20% cura產生的支撐，然後有點進去自訂那邊取消勾選Preload Extruder Retraction的選項，其他參數都沒動過
Adrian Li 2018-09-18 00:12:50
這漂移的樣子，會不會是硬體出事(例如桿子不順)？
黃俊傑 2018-09-18 00:31:11
看起來是沒黏住底板而已吧...
Adrian Li 2018-09-18 00:37:39
開個大一點的brim譲飛船先黏得住底板，底板温度設65C。
王仁雄 2018-09-18 01:21:57
感覺是定位跑了... 這隻印起來很漂亮喔
邢鳳言 2018-09-18 04:51:27
Moko Jenson Huang 2018-09-18 05:02:22
空間跳躍失敗了。。。
SonicSy Yu 2018-09-18 09:25:21
感謝Adrian大的建議，我把它改成平躺跟提高底板溫度就成功印出來了！
SonicSy Yu 2018-09-18 09:25:27
原文網址 Birk Binnard 2018-09-13 12:32:29
HexBox2
STL files and more info is here:
https://www.thingiverse.com/thing:3097841
https://pinshape.com/items/47258-3d-printed-hexbox2
曾荐宏 2018-09-13 14:40:26
Simiar
原文網址 黃瑞隆 2018-09-05 16:05:11
請問Simplify3D要如何設定ATOM 2.5EX雙色列印功能 請問Simplify3D要如何設定ATOM 2.5EX雙色列印功能
廖新弘 2018-09-05 16:33:23
先爬一下文，就知道了
Moko Jenson Huang 2018-09-05 17:09:04
找 Hawke ChienSheng Liu 兄
Hawke ChienSheng Liu 2018-09-05 17:53:31
黃瑞隆 2018-09-05 18:50:46
Hawke兄可以請您指導一下嗎
Hawke ChienSheng Liu 2018-09-05 19:00:37
先容我問一下，怎麼lag了兩年才問這問題？
黃瑞隆 2018-09-05 19:10:58
最近才剛升級至2.5 EX 呵呵~
廖新弘 2018-09-05 21:16:52
https://www.facebook.com/groups/atom3dp/permalink/1828404384064515/
黃瑞隆 2018-09-05 21:50:49
謝謝廖大 有空趕快來試試看
Hawke ChienSheng Liu 2018-09-07 23:39:36
請慢用 https://drive.google.com/open......
黃瑞隆 2018-09-10 16:19:08
感謝Hawke大分享
Hawke ChienSheng Liu 2018-09-10 17:34:41
要謝謝原創的黃大丙，不知道還在不在社團內⋯⋯
原文網址 Jörg Johow 2018-09-02 04:33:42
Is there any higher firmware for the 2.0 (single extruder) than 2.0.7. ? When I upload ver.180529 or 1805329 - it seems to be the firmware for the 2.5 EX printer. On the website, it is said, that the new firmwares are working for the 2.0 printer. Please help! Thx!!
戴亙泰 2018-09-02 06:12:38
Hello，you can use the firmware ver. 180529，and choose version 2.0，menu position :Control -> Version，change this item and then Store Memory，and then can be use version 2.0~
原文網址 Moko Jenson Huang 2018-09-01 06:12:26
點擊可展開 You Gotta See This triangle-down triangle-up share 分享 你好像無法播放這段影片。如果是的話，請重新啟動瀏覽器。 關閉 2018's Biggest Innovation For Camera Protection! 由 You Gotta See This 張貼 追蹤 取消追蹤 14,128,666 次觀看 瞭解詳情 KuvrdCamera.com 再看一次 繼續播放影片 瞭解詳情 KuvrdCamera.com KuvrdCamera.com 2018's Biggest Innovation For Camera Protection! You gotta see this... 瞭解詳情 14,128,666 次觀看 You Gotta See This 說這專頁讚 2018年5月1日
Exciting times for camera owners! ?
In March of 2018, over four thousand photographers pledged $303,979 for this Universal lens cap... Now it's here!!! ?
Learn more: http://bit.ly/GETKUVRD
Wing Wong 2018-09-01 20:13:10
好明顯係矽膠啦!
Moko Jenson Huang 2018-09-02 09:10:45
好似可以自己建模灌膠？
Moko Jenson Huang 2018-09-02 10:44:47
（紙上談兵一下） 請教一下，像這樣的模型， 灌入矽膠後，成功的機會大嗎？ （ ＃ 自己都覺得這問題好模糊啊 ） （ ＃ 矽膠都有分種類嗎 ？有建議的嗎？） ?
Moko Jenson Huang 2018-09-02 10:46:09
Fig 2
Kaku Chun Wa 2018-09-02 11:16:07
保護包覆我能信 但摔和泡水……
Moko Jenson Huang 2018-09-02 11:17:24
廣告總是要拍的比較吸引人一點。
Kaku Chun Wa 2018-09-02 11:19:04
Moko Jenson Huang 鏡頭的重量和矽膠的厚度 用重力加速度來看……外好內損 哭哭
Wing Wong 2018-09-02 15:07:39
放心!好快有淘寶版!
Moko Jenson Huang 2018-09-02 15:13:48
但是我想刻上自己公司名。 ?
Moko Jenson Huang 2018-09-13 14:01:27
https://www.facebook.com/moko999jp/videos/582833802132732/
原文網址 Richard Freeman 2018-08-28 21:55:21
Hello, I have Atom 2.5 EX, I am having trouble with dual extrusion printing. Does someone have a SIMPLIFY 3D settings file for dual printing? Thank you all for your help!
吳祉毅 2018-08-28 22:03:33
https://www.thingiverse.com/thing:533814
原文網址 Shih-Hsin Chao-Sushi 2018-08-28 17:34:22
各位好, 小弟想售出一組 ATOM 2.0 專用升級雙擠出 EX 套件組. 原盒未拆, 原價 8800元, 意者私訊價格, 謝謝.
Ken Lam 2018-08-30 11:16:28
最平可以多少
原文網址 Hawke ChienSheng Liu 2018-08-20 17:14:25
ATOM 2.5 世代交替，趁此時機入手名機套件，再適合不過。 看過太多新手組裝的機器，有時恨不得把它拆了重組…… 還是讓老師帶您組裝吧，名機才能發揮該有的效能。
ATOM 2.5 / 2.5EX 組裝工作營，一直開、開到出清，可以來報名、也可以來包班哦。
全不選 發文排行
