ATOM 3D Printer Group 造訪社團 » 線材相關話題

請問價格是？

排

不好意思!價格已PO在文內了...不包含小蟻攝影機歐!

有改機升級這價位算合理。
倒是對木工跟皮件有興趣，不知道你打算用什麼機台作那些事？

已售出給老朋友了....感謝各位!

早安，我的上半身也好了。

提高噴嘴溫度再試試。
中國廠家生產的料，不是每家的條件都一樣。 …… 查看更多

可以手動擠料試看看出料的情況,喉管多久沒換了呢,噴頭有沒清過,我之前才有印到出料不順,最後堵頭,清了噴頭ok 了

溫度高一點200~210試試看

是優線嗎，我一開始也是，後來拉到210就優了

温度加高好像問題就少了、不過感覺成品就是料的質素好壞有別啦

溫度降低ㄧ點,我前次初體驗溫度設190無回抽,狀況沒這麼嚴重.

There are lots of blobs on the surface. That means the retraction speed and length may still need to adjust.

超強 ~ 不過與我印象中的拳四郎有一點點小差別
期待你下一個作品是賽魯 ( 其實是求求你~Orz )

賽魯是啥?

人像真難畫~

http://blog.udn.com/....../snowcome/f_4170882_1.jpg

頂出來。

拿下來的當鞭子用 甩ㄧ甩

快速接頭的鐵氟龍管取下(進出端)~可以利用未受潮的pla線段從距離長的那一端往短的那一方頂出~或者試著甩甩看(我是沒試過啦!!)

先退開擠料機那端的鐵氟龍管，再退開噴頭那端的鐵氟龍管，PLA就可以處理了，如果斷了就用一段長一點的PLA通進去鐵氟龍管，就可以推出去斷了PLA，如果是噴頭啫料而造成斷料，方法同上面，只是最後要噴頭預熱下，用手去擠PLA，看到有PLA從噴嘴跑出來，快速抽離PLA，再降溫後復原所有零件，再次重新進料

加熱兩百度, 就熔了~

斷線我試過把線剪尖了去推裡面那截還是可以印(要關回抽)(還是很高機率卡在噴頭平台那 反正開快速接頭推一推就好)

I used to have long string too, after I made some adjustments to push the PTFE in hotend fimed, the string length became dramatically shortened,

Something happened to the translation - hotels fimed?

typo, hotels --> hole

You can have some procedures to avoid this issue.

"hotend", spell check problem...

For example, each time when you finish printing with any filament, move hotend aside and extrude some filament out from hotend then retract quickly. (So this string will be as short as possible)

Then pull this filament back after the Y tube to have a clear path to put another filament in.

It's not difficult to do this, but a little bothering.

Hi Charlie - that's exactly what Simplify3D does when it makes a tool change. I found that it works pretty well for small parts, but most of mine are large and for a large one (print time more than say 3 - 5 hours) I consistently got a clogged hotend.

This, in turn, required complete disassembly of the hot end and torching the nozzle with a propane torch to clean out carbonized filament. Since doing this requires cutting & re-soldering wires there are only so many times this can be done before spare parts are needed.

it means your nozzle has something wrong. I think these may happen in your system:
1. Cooling fan is not perform well to cold the nozzle down. (the throat)
2. The thermal resistance of your nozzle is too high.
3. The O-ring is mal-function to resist the thermal passing through.
4. The PTFE tube transfer too much heat from the head to the filament.

You should try to make sure all these works fine, not clean them every time. XDD

Thanks Charlie - I see what you mean now. What you say is certainly possible since my hotend is comprised of parts from 2.0 & 2.5 EX and is totally non-standard. I'll try some different configurations and see what I can figure out.

I think I may have solved this problem. Here is my blog page explaining what happened and what I did to fix things: http://wp.me/P8JtoQ-96

I also have this issue

I tried to push the ptfe tube as deep as I could but still

Did you try to push the ptfe by rotating it at the same time with the heated nozzle? This would make it even closer to the bottom.

Dennis Chen no ididn't thanks

推botfeeXXX

效果還不錯阿!!

用PVA開support應該要開好開滿啊，看起來你還有留gap