ATOM 3D Printer Group 造訪社團 » 線材相關話題

請問是spider-flex tpe？

好讚的分享!! ?

想問問 回抽量跟回抽速度

好可愛

這是沙發本人

超帥

我現在都很少印木質PLA，因為有時候會遇到比較大的顆粒，就容易會堵料 ?

有時候很順 有時候就是卡一整天 ? ?

蔡欣燁 就很偶發 ? 後來就不太用這種複合料了

印象中有聽說溫度要比較高一點，這樣流動性會比較好

明顯有顆粒填充的線材換大口徑的噴嘴會比較適合

你們需要的是這個 XD
只要能轉接一般接頭的話，很多問題都不是問題。

https://www.facebook.com/groups/atom3dp/permalink/2438182293086718/

求講解 ?

木質的溫度也不能拉太高吧我不確定

下次試試看

轉接頭可以轉接使用E3D或是MK系列的噴嘴。這表示你堵料時，可以輕易更換噴嘴。同時可以更換不同口徑的噴嘴。

堵料是一定會發生的事，但原廠的硬體比較沒辦法讓使用者方便的更換或調整。

懂了懂了 我在來研究研究 感謝

其實進料輥輪如果改成2.5版那樣加裝二段鐡氟龍管，比較不用怕軟料跑出來

有人調機真好，我都因為機子不太會調，穩定度不好，久久才會去印一次

這什麼料？

超強

I’m waiting for Duet2 to upgrade my Atom2.5ex, also want to try the smart effector.

Why not switch to 32bits motherboard ?

要試試蜘蛛家的嗎？

露天

我是習慣用彩家的補充包，感覺比較環保

貿祥的線材不錯用，就是露天的3dpw

有推薦的連結嗎？

羽耀吧
https://class.ruten.com.tw/user/index00.php?s=feasun3d......

明燿線材不錯

可以參考一下
https://shopee.tw/product/11658144/2001892476?smtt=0.0.9

Is it actually the bed or no?

It looks like it thinks the printing bed is larger than it actually is

I've been printing on that exact same bed configuration for over a year. All of a sudden the printer seem to lose track of where Z equals 0 is. I have no idea what the problem actually is.

Yea, no idea. I'd replace the motherboard and see what happens.

I've had the same thought. Do you have any suggestion on which MB would be a good replacement? (Good = will run with vanilla Ta At om2 firmware.)

WOW really crazy @_@

If the touch sensor can work well, u may change the printing area by using smaller diameter, like 210 or 200 to c if it can work or not.

or u just change the spring on the screw of touch sensor? maybe the spring too hard for touch sensor?

I remember at one point I was using a different board that wasn't from the Atom dudes and my prints were always just not perfect. It could have been me and my settings, but they were off. I also had to reverse some numbers in the settings to get the other board to work. At some point I bought another new Atom board and started using that. Let me look up the non-atom board

MKS BaseV1.2 3D Printer Controller Board (RAMPS 1.4 + Arduino 2560 remix board)

this was the name of the board. I bought it on Amazon from Keyes themselves but the item is no longer on Atom being sold by them.

and that was recommended by the Atom dudes as a replacement for not using their board

Hmm mm. Not exactly encouraging. I'll do some research and see what I can find.

看到真懷念剛裝好atom那時的情景

Cherub Shiao The sensor is the standard Atom2 micro-switch. It works fine ; the auto level function runs perfectly up to the place shown in the video.

Amazon has that board for $37.77 which is fine. But it has a different shape which means the mounting holes will be different, so attaching it to the Atom2 frame will not be simple.

Also it looks like the stepper drivers are soldered to the board and not plugged into connectors on the board. This means there's no way to replace a driver if one goes bad. I've saved an old/bad Atom2 board just to have some backup stepper drivers if needed.

Remove the spring during bed leveling

Dan Salvador That's an interesting suggestion that would never have occurred to me. I don't see why it would change anything, but I'll give it a try and post results here. Thanks.

I was really surprised, but removing the spring allowed AutoLevel to complete OK.

But now I have a different problem - the printer fails to remember the Z-Offset setting. Each time I set it and then do Adjust Offset the printer behaves like the offfset has not been set. I may be able to compensate for this by setting a Z-Offset value in my slicer.

Birk Binnard well known issue , during the first print after the bed leveling adjust the offset

Well it certainly wasn't well known by me! But thanks for the info.

I haven't been able to make a first print since completing the bed leveling because the printer crashes the hotend into the bed as soon as it starts to print. And I have re-adjusted the offset after this happened and it didn't fix the problem.

I'll go through the whole process again and see what happens.

Since the AutoLevel completed OK (after removing the spring from the Z-Min adjuster screw) I thought I'd try Auto Calibration to see if that helped things at all. But that function crashed the hotend into the print bed on the 4th move. So there is still something wacked with the printer.

I wish I knew what it was.

After a considerable time testing and checking I found 2 problems, one of which I was able to correct:
1. The small metal flap on the Z-Min micro switch was disconnected from the switch and stuck, by magnetic attraction, to the inside of the end effect or frame. The flap is small enough to hide inside the curve of the frame, so it was difficult to spot. But I finally did find it and after partially disassembling the hotend was able to reinstall it on the bottom of the microswitch.
After this I was able to successfully complete an Auto-Level and Z-Offset adjustment - sort of (see #2.)
2. I'm beginning to suspect some sort of internal EEPROM error because the Z-Offset value keeps getting messed up. Here's a typical scenario:
Perform Adjust Offset and set proper offset using the LCD knob
Perform Adjust Offset again to verify it is OK. It isn't.
Check Z-Offset value on LCD. It is far different from what it should be
Change Z-Offset vaue to 0.00
Perform Adjust Offset again and re-adjust to proper value
Check Z-Offset on LCD - this time it matches previous setting
Run test print with Layer Height = 0.200 mm
First layer prints ok, second layer shows 0.300 for part of the layer, then switches to 0.400, third layer shows 0.400 then switches to 0.500
Stop print and check Z-Offset; it shows 1.32 which is far off from previously set value.

All this leads me to believe I do need a new motherboard.

Birk Binnard I had an issue before where my z offset like yours would just do wild stuff. That was the first time I replaced my board. Second time I replaced it was when I had that shirt I showed you way back in messenger.

Well I'm going to try a different slicer just to ensure it really is a printer problem. I don't much like the idea of replacing the motherboard, but I've done it before so at least I know what to expect.

Well there is definitely something wrong with the way the printer handles Z values. I used a different slicer (Craftware) and had similar issues with the printer's Z height when printing.

My layer height is set to 0.200 mm, but after printing the fir st layer, layer 2 showed 0.100 mm for a while, and I could hear the nozzle tip dragging over the traces from layer 1. Before layer 2 was finished the LCD switched it's display to 0.200, but that didn't seem to make any difference with how the printer was printing.

Layer 3, which should have been at height 0.400, showed as 0.300 and had the same dragging effect as layer 2. I stopped the print soon after noticing this.

So similar results from 2 different slices printing the same part makes it pretty clear there is some sort of problem with the printer itself. I thought about a bug in a stepper motor or stepper motor driver, but if that were the case the hotend X-Y position would be off from what it should be, and it's not. Only the Z value seems to be wrong.

This suggests there is either something wrong with the firmware itself, or with the way the motherboard's firmware is processing the input GCode. So it looks like I need to find a new motherboard.

?

M503 dump setting
M501 Try to restore failsafe default
M503 dump setting again.
M500 for save setting

Thanks Clarence - I will try that. But I doubt I'll be able to make sense of the EEPROM data.

OK - I tried that series of commands. They seemed to work OK. But printer still doesn't handle Z-Offset properly. When I do Adjust Offset the printer needs an adjustment of 1.350 mm to position the hotend at the proper height. After I do this the Z-Off set reading says 3.175. Then, if I go back and do Adjust Offset and re-adjust to 1.350 the Z-Offset value says 6.10.

Of course I know that Z-Offset is limited to +/- 2.00, so there is something very strange (at least to me) going on here.

I've got the text of those M commands if you want to take the time to look at it. Can't post them here (of course - FB is such a pain) but let me know if you want to see the output. Meanwhile I've been looking at possible replacement motherboards.

How about check the belt, wheel etc. Might need to consider something loose in mechanical.

Been there/Done that. All is OK.

Even if that were the case it wouldn't explain the Z-Offset values being so strange.

It's the farest edge, consider the cable might cause sensor not work as expect at the specific place. Try to loosen some signal cable length

OK - thanks. I'll check all the stepper motor cable connections. That is something I had not thought about.

Nope - all the cable connections are OK - I checked both ends of each. I also made sure the stepper chips were all firmly set in their sockets - they were.