ATOM 3D Printer Group 造訪社團 » 線材相關話題

溫度不對

應該是高 我猜

溫度太高,而且有水氣了,如果要表面好看可以考慮用220以下列印

我之前測別家軟料，上195度 中 210度 下230度 . 哪家軟料我倒是不知道～哈哈 供參考！

tpee軟料...........大概這樣.............

要看你用的是什麼料，基本上外觀都不太會這樣，tpu的話，大約 195-215度(一般)，若是atom原廠料tpee，大約 215-235都應該ok。其它的料我就沒多測了。

印太快容易起疙瘩

Nice!

geckotek is nice, too.

影片為證～順暢多了！

接下來就是耐用度了

太強了...

畫圖容易 測量難呀 請問大大有掃描儀器嗎 要不然那個齒輪和溝槽 不是用游標卡尺就量的出來的呀

對啊！看到螺牙我就高潮了..@@

太陽曬會不會軟掉啊？

大大太厲害了 SW高手,希望看到大大的耐用程度的分享,......之前有看過文寫, 齒輪類建議立起來列印,結合程度會比較好(純參考)

I need stl file please :)

向大大請教 大大是使用一般的PLA-----還是比較有點任性的PLA+

靠 這真的太屌了～

猛

太厲害了！

應該撐不了多久就崩解了

好強！

Jay Chao

Is your ATOM 1.0 or 2.0？

2.0

Maybe original lcd didn't broken? Might be you use the wrong fw,
the fw version end with b is for ATOM 1.x.

I had that plugged in since march and it worked fine. It just recently broken. So that white tab is ONLY for Atom 1.0? You sure, cause I say the online instructions and it shows the guy putting that in I believe.

also what do you mean by fw?

Did you upgrade Firmware(fw) via arduino IDE recently ?

oh firmware... I upgraded to 2.7, then back down to 2.4

And it worked fine for like 2 days

the new screen works and the old screen doesn't. Same firmware and all.

But did you use the firmware version end with b?
Since ATOM 2.0 firmware can't support this LCD without "ATOM use" pin without modification.
It's highly possible you are using the wrong version firmware 2.04b (it's for ATOM1.x)
But, it might be ok now, just dont' restore fail safe.
Otherwise, remember to set steps/mm to 160 for X,Y,Z axis. & 200 for E axis & save.

Just a reminder, if you don't understand what I am talking about.
It's ok, once when you got problem in the future, it might help.

Right now I am not using any firmware as I installed a new board.

So this is how it went. The screen was messed up. I got told by another user I somehow fried the board with my hotend themostat. So I bought a new board AND a new screen. The new board came first. I installed it and the screen was still messed up. I got the new screen today, put the new screen in and it works fine. So I'm thinking it's the screen.

You're asking if it's the firmware which it's not, because when I installed the firmware it worked. It worked for days on 2.7 and when I went back to 2.4. So if it was the firmware, it shouldn't have worked the moment I installed it right?

But seriously, what does the white plug do?

so this new screen can't be used in atmo 2.0 without the ATOM USE plug?

Sign, you didn't explained what controller board you are using clearly.....
The "ATOM use" plug is designed for ATOM2.0. (you always understand as reversed.) So, it's for the ATOM 2.0(not firmware version, I am talking about model) firmware only work s with it connected.

The firmware version number end with b (like 2.0.4b) it's for ATOM1.0~1.x model.

So, what is your new controller board? It's ramps1.4 or MKS Gen?
What is your step stick now? A4988 or DRV8825?

Whatever, if yours works fine. It's fine.

He is official support, you can ask him more ;p

the controller board I'm using is this

https://www.amazon.com/....../ref=oh_aui_detailpage......

The Atom guys said that would work.

So the plug is for Atom 2.0. So that plug literally makes the firmware for Atom 2.0 work? I wasn't using any firmware with a b at the end. If I were, wouldn't the screen have stopped working as soon as I installed the firmware and not after? To be clear, the screen stopped working when I was using the controller board I got from Atom 2.0

Sign, so tired to explain that. Check LCD2004 4bits, 8bits parallel control by yourself.

Answer this question, if the wrong firmware was installed on the original atom 2.0 controller board, why did the screen work for days just fine and then stop?

If you use firmware like 2.0.4b on original LCD , it still possible to display correctly.(just sometimes might mess up) Since 4 bit's LCD connection still there. It's backward compatible. The much serious problem is what's your stepstick using now? A4988 or DRV8825. The steps/mm difference.

I'm going to put back in the old board and install the latest firmware for Atom 2.0 which I think is 2.0.7 and see if it works.

this is what the screen was looking like before

Since your new controller board is the same, actually you can plug the "ATOM use" pins on new controller board. Just find out the same place same pins.

I did, but there's no where to plug that into the new screen. Also I'm rechecking my downloads and I only installed the 2.0.4 and 2.0.7. None of these were version B.

reinstalled the firmware and the screen still doesn't work. Going to try firmware B with the new screen since it doesn't have a "ATOM USE" on it

as expected, 2.0.4 doesn't work on the old screen or new screen. 2.0.5b works on the new screen. So I'm coming to the conclusion my old screen from Atom is just broken. Is there anywhere to buy that screen from other than Atom?

Yinka Alade No, it's customized for ATOM. Never seem it in other place.
BTW, Check your stepstick. If you are using 2.0.5b on "new controller board" but stepstick is DRV8825. need to change the steps/mm as previous mentioned.

I honestly have no idea what a stepstick is. How do I check that?

Who is official support? Hawke ChienSheng ?

http://reprap.org/....../A4988_vs_DRV8825_Chinese......

黃俊傑

I get it now. I took the A4988 chips off of the Atom board and put them onto the new board

So when i comes to firmware 2.0.X and 2.0.Xb... does this change print quality at all?

hmmm from original ATOM board, it's "DRV8825"

Check your steps/mm in LCD menu X,Y,Z E should set to
160,160,160,200

oh, if that's the case, then the chips I took off are "DRV8825". Which ever, I took them off of the ATOM main board. I'll check the LCD panel right now.

right now they're set to half

80, 80, 80, 100

So I can set to double manually and that will be good?

yes, you should double it & store memory

ok. got it all changed and now I'm about to put this stuff back together and do a test print.

I really appreciate all that help, Clarence !

Sometimes the light that turns on the board when the hotend heats up starts flashing. Is that normal?

Yinka Alade if it's the MOS for hotend heater , it's normal

Sorry, one more question, lol.

I have 2 hotends. One brand new from Atom and one i changed the blue and yellow wires for. The brand new one heats up quickly and perfect. The one i changed wires for heats up slower but reaches 200. However it cant reach 240 and stops at 230. You have any idea what the issue could be?

assembly issue , wire issue , thermistor or heater quality/condition.(check via multimeter, compare the resistor value on heater)

got my test prints done and everything looks good. Thanks again Clarence

Birk Binnard the answer is in here. It delt with chaning the steps

"Check your steps/mm in LCD menu X,Y,Z E should set to
160,160,160,200"

Yinka Alade Is that in the configuration.h file? Or somewhere else?

Birk Binnard in the menu in the LCD.

I thought the lcd menu text was somewhere in configuration.h

Birk Binnard could be. I’ve never messed with that file.

Ok. I'll see what I can find.

OK - I found it: the Steps values are in the LCD menu itself, not in any code module. The values are at the end of the Control/Motion screen. Mine are currently set to +160,+160,+160,+0200 so it looks like I should be good to go once I get the new board installed and loaded with my current firmware.

請問你是掃描然後打印一模一樣的出來??
還是自己畫設計圖???

非常搭配 XD

請問這個剖面的功能是怎麼做的?

像原配的 好看喔!

帥唷！..很漂亮

這張比較接近實際顏色

我有PLA/ABS 的問題，塑型冷卻後這到底可不可用在餐具?
也有看過笛子的~
安不安全?