管理員
統計數據
原文網址 Birk Binnard 2019-05-09 05:06:32
Never mind - I fixed it by installing an OLD version of Arduino: Ver. 1.0.5-r2 (whatever that is)
Error uploading firmware
I get this error uploading current ATOM-208B-20180329-Firmware using Arduino 1.8.9 to my Atom2:
Sketch uses 119194 bytes (46%) of program storage space. Maximum is 253952 bytes. Global variables use 4712 bytes (57%) of dynamic memory, leaving 3480 bytes for local variables. Maximum is 8192 bytes. java.io.IOException: Cannot run program "___REMOVE___/bin/avrdude": CreateProcess error=2, The system cannot find the file specified at java.lang.ProcessBuilder.start(ProcessBuilder.java:1048) at processing.app.helpers.ProcessUtils.exec(ProcessUtils.java:26)
Google found another person with this same error on 17 May 2019 but there was no fix given. Could it be a JAVA bug?
原文網址 Martial Geudin 2019-04-25 17:38:05
I have the MMU2S from Prusa and have the idea to mount it on my Atom 2.5. The MMU is a multi-material selector that can manage up to 5 different filaments. This means that you could build a part in 5 different materials. Or use some special filament as for support that can be desolved by water or limonene. Using different materials will ask different temperature management as other parameters linked to the material. Does anyone though about this and build it on his Atom-printer? Any information is welcome. I think the software, firmware is the big question.
原文網址 Todd Whetstone 2019-03-23 14:48:19
When trying to auto level my Neutron, this is what I get. The effector wont go all the down to the build plate, it stays some where around 140-150mm above the plate, goes through all the motion of leveling, but does nothing. I increased my build height from 200mm to 220mm, but I'm not sure where to change it in the firmware. Any help would be very much appreciated. I'm excited to get printing.
James Lin 2019-03-23 14:58:59
這台好像沒這麼高~
Yohann Toutain 2019-03-23 18:27:10
First use the height by default (225 if i remember), then in your Marlin firmware, you should have this line: # define DEFAULT_AXIS_STEPS_PER_UNIT, increase the values on X, Y and Z until you can do the auto leveling properly. Then make some XYZ cubes test to verify if it respect the good tolerances and adjust if necessary. If you have problems of under or over extrusion you will have to do the same for the E.
Malak Ghorghi 2019-03-23 19:30:26
Hugo Lopez Uria here a nice conversation I saw maybe to be useful for you.
邢鳳言 2019-03-25 04:33:43
# define DELTA_HEIGHT 230 // get this value from auto calibrate in my case, to make sure the bed would be probable.
原文網址 Josh García 2019-03-12 17:08:42
Hi group, I have an ATOM 2.5 FX and i'm trying to enable a run out filament sensor. Any one know if its posible with the last firmware? Thanks
Jose Antonio Fernandez Camero 2019-03-23 00:14:46
Hi Josh, I have a customer with the same problem, did you fixed it?
Jose Antonio Fernandez Camero 2019-03-23 00:15:46
I don't have to much time this days to investigate... he already did that on 2 printers, but in ATOM 2.5 FX is not working
原文網址 Hugo Lopez Uria 2019-02-14 21:52:14
Atom 2.0 E3Dv6 + custom effector + bondtech. I cant get negative values in the zoffset to adjust the new probe. Any idea of firmware parameters? (V.2.0.6)
Malak Ghorghi 2019-02-15 00:07:31
Hi there could you please give me the stl file or the cad file of the effector you have printed?!
原文網址 Yohann Toutain 2019-01-23 19:38:32
Yes! I made it! After configuring steps in Marlin, here is the result: A 20 by 20 by 19.5 mm cube, a bit squeezed on Z but yes, it work!
Radek Taunus Henys 2019-01-23 19:54:03
Really loud print but nice result
Stanley Chen 2019-01-23 23:21:26
nice job!
原文網址 Yohann Toutain 2019-01-12 06:18:24
Hello Everyone.
I need your help about my project of Neutron 3d printer. The configuration of my mother board in Marlin is:RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan). Here is my problem: i can't move the X and Y axis when i go to Prepare -> Auto Home, only the Z axis move. When i go to Prepare -> Move axis and choose a length for the X or Y axis, only the Z axis move. What i have doing wrong??
Yohann Toutain 2019-01-19 07:18:39
I have found the problem, my Ramps was defective...
原文網址 陳永慶 2019-01-01 15:51:37
想請教有沒有其他朋友也用過Smoother? 我想裝不是對列印品質有不滿，但是Atom2.5在高速列印的時候，高頻的噪音真的蠻大的，感覺上裝了smoother有比較安靜一點 有人有同樣的經驗嗎？ 另外想請教有沒有人有長期使用經驗的，是否會對driver有不良的影響？
James Lin 2019-01-01 16:34:06
品質有改善嗎? 哪裡買的? 你的是八顆,標準是幾顆元件?
Dennis Chen 2019-01-01 18:40:39
我裝很久了，也有長時間列印，馬達聲音有比較小，品質並不會明顯變好，但跑某些曲線時，抖動的紋路有消失
Pinocchio Faken 2019-01-02 00:15:45
與其這個，不如TMC...
施圳溪 2019-01-02 08:29:23
看一下 http://diy3dprint.blogspot.com/2016/05/3d.html
原文網址 Joe Abaquin Bing Aquino 2018-12-29 02:23:34
Question: I have the Atom 2.0 and I know I updated the firmware to 2.0.7 which also reads out in the screen.
My question now, is my printer ready for heat-bed upgrade? Or do I still need to update to different version?
I have bought all the necessary stuff to install a heat-bed, did my research and very confident now that I won’t burn the house. Greatly appreciate for any response guys.
原文網址 Birk Binnard 2018-12-28 03:24:16
Has my Atom2 Motherboard gone crazy?
When I issue a Home command from the control panel the X & Y columns do the right thing, but the Z column moves down about 1 CM total. The video shows this. The same thing happens happens when I use the Home All command from the S3D Machine Control panel.
However, if I sends command from S3D to move up or down they work OK. The X, Y, and Z columns also move correctly on an individual basis. So I think the steppers are all working OK.
I tried Reload FailSafe and that did not change anything.
Could this be caused by a short in the Z Limit switch or wiring? I've got a replacement limit switch I can swap in if necessary. Or should I try reloading the firmware?
黃震桀 2018-12-28 03:34:08
check Button line use Electric meter and motherboard hole maybe just with ease
Birk Binnard 2018-12-28 04:52:32
Reloading firmware did not help. I swapped stepper controller circuit boards between 2nd extruder (which I know works but don't use) and Z stepper - no change in behavior. Found problem II hope) : Motherboard is not getting signal from Z-Min endstop. Must have broken wire someplace.
Justin Nardone 2018-12-28 06:55:17
Shouldn’t the end stop it be plugged into the Z Max socket on the Atom board?
Birk Binnard 2018-12-28 07:33:40
Yes, and it is. But I've unplugged both wires from the motherboard and connected them to a multimeter. The meter reads nothing when the end stop is depressed. So either the end stop itself is bad or there's a broken wire somewhere. What' confusing to me is why that kind of problem would produce the results shown in the video. I would guess the Z-axis would just crash into the top of the rail and keep trying to go up. But this is not what happens at all.
Birk Binnard 2018-12-28 08:17:05
I hooked up an extra switch to the Z-Max motherboard connectors using it's own wires. It works OK. So it's either the original switch or the wires between it and the motherboard that is bad. I'll try using this switch on the Z columns to see if that fixes the Home issue.
Birk Binnard 2018-12-28 09:02:28
The new switch and wires work OK. Now I have to figure out if the original problem is bad wiring or a bad switch.
Justin Nardone 2018-12-28 12:05:44
If the switch is wired NC (normally closed) that is exactly the behavior you should get. That prevents the motor from moving up in a homing situation. I.e if a wire or the switch is broken with a NC setup the motor won’t smash against the top of the printer and potentially damage it. If you have a Normally Open system with a broken wire the system won’t know either way and would hit the end of travel.
Birk Binnard 2018-12-28 13:26:47
Atom doesn't tell us if the switches are NC or NO. My guess is NO. But in either case I still have to figure out if it's the switch or wiring that's bad. I'm hoping it's the switch because I don't think it's possible to replace the wiring without disassembling 1/3 of the printer.
Ya Hsuan Wu 2018-12-29 02:32:55
you can try to Restore memory & run Auto calibration & auto level
Birk Binnard 2018-12-29 03:07:54
Surprisingly the problem was a bad micro-switch. This was fortuitous because I was able to use the existing wires. It was a bit tricky splicing in the leads from the new switch, but I was able to do it without breaking anything else.
討論主題
全不選 主題相關關鍵字
