ATOM 3D Printer Group 造訪社團 » 耗材 模組 副廠零件

噴水，再抹ㄧ抹，抹平後直接印，不足再補點新的口紅膠，
不需要洗掉，太浪費
ATOM送的那罐我才用不到一半

感謝

拆下來用水洗一洗比較乾淨~弄乾後再裝上
或者是用刮刀刮除用過的部位~其餘部位可以不刮除

噴點水抹開，然後再用吹風機吹乾。

忘了強調一件事：這個組裝工作營的內容，與ATOM規劃的是一樣的；但是個人我在參與實習時，發現學員素質不一的狀況下，課程進度很容易拖延，造成第二天有關機器校正保養、切片軟體使用等的部份，時間不夠只能講一點！
所以我會另行規劃一天的「使用工作營」給想要更熟悉ATOM 2.0 及3D列印的同好報名，主題是組裝工作營Day2的內容，已經報名APPLE&ORANGE組裝工作營的同好，可以免費參加哦！

印的超好的

只能說ＡＴＯＭ團隊太強了！研發出此產品 , 還賣到缺貨 , 台灣之光啊.....擺設過程中 , 成品過於圓滑 , 還要用相機蓋去做靠面 , 不然會一直滾動！！

切片程式是KISSlicer嗎？感覺CURA跟KISSlicer一樣的速度設定，實際速度不太一樣，所以有此一問

是KISSlicer喔！！

自爆一下，後面幾張照片有看到是KISSlicer

近乎完美

25mm/s * 78% ~ 82% = 19.5 ~ 20.5 mm/s

WOW!不好意思什麼是"過橋"啊?

這就是過橋 https://youtu.be/7WSKhHEpB04
BTW,這篇應該夠格放精華區了XD

超級漂亮！！

別這麼說！這裏殺手級的怪物一堆！！

一天就變高手

政霖....我都不知道這個讚要不要按了.....臉紅

哈哈哈哈

黑色那個是橡皮筋嗎??

是O-ring 吧

其實我一開始還以為是水龍頭的止水栓

好赞！大陆精度就没这么好！求配件自己配！

Atom2.0很值得買啊、都幫你配好好的！

我论在大陆啊！

嗯...有難度！就算友人幫忙帶去、組裝上也是一個問題！

目前参加众筹999rmb套件，组装中，感觉细节，流程，教程，固件调试都非常重要！

然後跑到3,4層（噴頭跟底板中間有空隙）的時候是沒有料擠出的

噴頭內也沒有卡料的情況

再把手冊翻過一次！會有不同的感受

ptfe管會被擠出來,一種是沒插到底...
另一種是快速接頭的爪子抓不住了...

把快速接頭固定住試試？之前偶爾會有幾層沒進料，卡緊之後好多了
https://www.facebook.com/groups/atom3dp/1605464206358535/

看一下這份調整方法~

Po-Hsun Peter Wu 我上次用你的方法調整之後就可以了而且很順利，可是我後來因為風扇問題把玻璃板拆開，後來又不行所以我又重新調整，可是現不轉怎麼調整都不ok

先用手晃玻璃板看會不會晃吧，還有就是把G29 後面的數值調高點，拉高列印時的高度囉 (或是你要放鬆螺絲也行啦)

How about adjust the metal plate and the fan position?

Clarence is correct - I had the same problem and fixed it by slightly adjusting the connections between the cover and the two side-blowing fans.

it looks like that the side-blowing fans not installed correctly

I installed the side-blowing fans with their blades facing towards extruder, not away from it like the above photo shows.

Does it matter, as long as the airflow opening is pointed down, towards the extruded filament?

if side-blowing fans towards extruder, it will inhale the air from the extruder, i think it will help nozzle throat temperature control, but not good for lower the temperature filament.(the source air temperature is higher then facing outside)

You are correct - I did install the fans backwards. So far I have not noticed any problems resulting from that so I will leave them alone for now. TIme will tell if I need to reverse them.

I think it depends, if it's too cold. Then reverse direction might be a good choice.

Yes. I'm in Sunny Southern California - it never gets cold here.

The Ball Screws had some oil?

Birk Binnard to start with I also faced the fans inwards towards the nozzle. I printed this way for about 50 hours. Then I wanted to turn them, but discovered that the bottom heat shield was bend the wrong way. I bend it out side in with a pair of pliers and re-installed everything according to manual. No dobt the colder air from outside cools better.
If you do need less cooling then simply set this in KISSLICER.

Check thermistor connector
Without loose
If there is no loose
It may be bad

Also check if there are any short between thermistor , heater and hotend.

We checked the wiring, nothing loose. Anyway to check short?

https://www.youtube.com/watch?v=dQ5B715tO4M

also measure the resistance on the thermistor
It might open circuit or broken

check the soldered spots first, it could be loose some where.

FYI - I had the same problem this morning but it recovered after set the temp in prontoface

In order to check soldered spots, do I have to cut open the black Heat-shrink tubing?

Lien Ted: Thanks, let me try to connect with prontoface.

Lien Ted: What Baud Rate you set to?

I used 250000. Click "set" and I had luck.

Lien Ted: When I click Set, this button not gray out (yours gray out) .

Winston Shieh yours is right. Mine grey out is due to disconnection.

When I click connect, I got the error
Connecting...
start
Printer is now online.
echo: External Reset
Marlin 1.0.0
echo: Last Updated: Apr 21 2015 17:52:06 | Author: (jcrocholl, Mini Kossel)
Compiled: Apr 21 2015
echo: Free Memory: 3777 PlannerBufferBytes: 1232
echo:Stored settings retrieved
echo:Steps per unit:
echo: M92 X160.00 Y160.00 Z160.00 E200.00
echo:Bed Level Matrix :
3.644 3.644 3.644 3.606 3.669 3.669 3.669
3.900 3.900 3.963 4.038 4.125 4.219 4.219
4.088 4.125 4.250 4.538 4.663 4.788 4.900
4.150 4.313 4.556 4.881 5.181 5.356 5.463
4.181 4.475 4.825 5.219 5.600 5.825 6.013
4.563 4.563 4.975 5.469 5.863 6.175 6.175
4.981 4.981 4.981 5.463 5.944 5.944 5.944
echo:Maximum feedrates (mm/s):
echo: M203 X300.00 Y300.00 Z300.00 E300.00
echo:Maximum Acceleration (mm/s2):
echo: M201 X3000 Y3000 Z3000 E9000
echo:Acceleration: S=acceleration, T=retract acceleration
echo: M204 S9000.00 T9000.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
echo: M205 S0.00 T0.00 B20000 X20.00 Z20.00 E5.00
echo:Home offset (mm):
echo: M206 X0.00 Y0.00 Z0.00
echo:PID settings:
echo: M301 P16.54 I1.30 D52.56
Error:0
[ERROR] Error:0

: Extruder switched off. MINTEMP triggered !
Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
[ERROR] Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)

echo:SD card ok

Anything wrong?

check the thermistor connection anyway, it's not detected.

列印聲音很大聲其實有點籠統呢，可以貼個影片來看看，目前可以試著把四塊晶片右邊的螺絲都調到0.45試看看

其實我比較愛用藍色膠帶、一條可以印超久^^

我還在找我附近在哪買

請問藍色膠帶的商品名稱是啥

ATOM 團購首發3M 2090 藍色膠帶大家有興趣嗎？

要自己買的話可以到http://tb.cn/zKPOIBy?sm=c9caf5

為什麼貼這個膠帶能防剝離呢? 它是雙面膠嗎? 看商品說明是"油漆作业中的遮蔽应用" 覺得疑惑...

一切盡在不言中、只推好東西^^

口紅膠就先隨便塗一塗, 再滴個幾滴水,
拿個菜瓜布刷一刷, 讓口紅膠跟水混在一起, 變成稀的口紅膠水~
然後就慢慢刷平, 等它乾, 就平整了~

3M 2090, 或 Kapton 也都不錯用, 好拆.
但我個人還是喜歡口紅膠, 黏的比較牢, 也不算太難拆

一起用派

油漆行不知買不買的到。

請問，藍色膠帶怎麼用？把玻璃貼起來就行了？

原則上膠帶只是讓第一層較容易咬住而已，所以只要貼平整就好