• #maker+t=market
  • 3D列印服務
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » CLI

原文網址 Jeff Johnson
2019-05-23 21:42:30

Z Wobble. I've just discovered that I have it. 2 days ago I printed by first model with flat sides and it was very obvious. I followed the manufacturers video and it had nearly no effect. The slider was already very tight. That's when I discovered a few problems all related to poor quality control.
1. The bearings in the slider are of such poor quality that it stutters significantly when it moves.
2. The lead screw or the stepper motor makes a click sound and a slight bump movement can be detected with each revolution.
3. The threads on the lead screw are very rough and the nut can't smoothly travel the full length under pressure.

After seeing that tightening the slider didn't help I decided to smooth out the lead screw. I first used the tip of a pin file to find a really rough and out of round section near the bottom of the screw. I filed the root and edge of the crest of the threads with a pin file and then finished it out with progressive grits of sandpaper from 400 to 2000. The Z Wobble has been significantly reduced as the picture shows, but that clicking is still there. My next step is to remove the motor assembly and see if there's some defect that's causing it to contact the frame as it spins. The click gets more severe if you pull the lead screw towards the front and disappears if you push it to the back.

I designed this Z Wobble test after seeing a couple others. It's curious that it causes a string of bubbles in exactly the same spot.

翻譯年糕

Marvel Mendoza
2019-05-24 02:47:28

Jeff Johnson
2019-05-24 02:56:02

Marvel Mendoza
2019-05-24 03:13:51

Jeff Johnson
2019-05-29 23:16:52

Vinicius Silva
2019-05-30 04:13:55

Fred Breton
2019-05-30 08:46:35

Fred Breton
2019-05-30 08:46:45

Jeff Johnson
2019-05-31 21:14:24

Jeff Johnson
2019-05-31 21:17:41

Jeff Johnson
2019-06-05 22:19:27

Jeff Johnson
2019-06-12 00:41:44

Jeff Johnson
2019-06-24 04:42:13


原文網址 Толик Лефтер
2019-05-22 03:45:53

Hello guys! Problem here! Printer (photon) restarts by itself without any errors after printing first Base layer, cant figure out whats the problem. Tryed resclicing a couple of times, doesnt help.

翻譯年糕

Hobby Mike
2019-05-22 03:49:35

Толик Лефтер
2019-05-22 03:50:32

James Wareham
2019-05-22 03:54:57

Толик Лефтер
2019-05-22 03:56:46

Clinton Hoines
2019-05-22 04:29:43

Andy Chung
2019-05-22 04:52:47

Ced Ric
2019-05-22 05:09:02

Silvestro Zitelli
2019-05-22 05:16:39

Nemo Vilpponen
2019-05-22 05:58:38

Joel Tarasiuk
2019-05-22 08:12:17

Silvestro Zitelli
2019-05-22 18:47:33

Paul Churchill
2019-05-23 06:30:51

Six Hatch
2019-05-23 20:31:50

Nemo Vilpponen
2019-05-24 01:13:39

Six Hatch
2019-05-24 15:59:43


原文網址 André Nettermann
2019-05-21 19:09:33

Is there currently an issue with the chitubox website? I've been trying to register but the page has been bugging out consistently. Doesn't react to anything being clicked and doesn't load completely. Tried it with several different browsers. anyone else having that problem?

翻譯年糕

Lukas Schult
2019-05-21 19:12:45

André Nettermann
2019-05-21 19:18:28

Bob Deblier
2019-05-21 19:45:04

Sen Kun
2019-05-21 19:45:51

Lukas Schult
2019-05-21 19:56:06

André Nettermann
2019-05-21 20:02:29

Lukas Schult
2019-05-21 20:34:14

Henry Adams
2019-05-22 11:53:31


原文網址 Mourni Tenchou
2019-05-20 04:13:30

So I've been using different slicers and I struggle hard with support placement. And it's not about where to supports its that I literally can't place them.

I see an island, E. G. The fist of a miniature floating around. After auto supports I try to add thin supports to the fingertips but when I click nothing happens. I've been using the anycubic slicer and chitubox - both gave me the problem. I'll update with a photo asap after restarting my pc.

翻譯年糕

Alex Vee
2019-05-20 04:18:03

Hugh Williams
2019-05-20 04:23:33

Mourni Tenchou
2019-05-20 04:23:33

Mourni Tenchou
2019-05-20 04:23:42

Mourni Tenchou
2019-05-20 04:24:00

Mourni Tenchou
2019-05-20 04:24:32

Mourni Tenchou
2019-05-20 04:25:05

Mourni Tenchou
2019-05-20 04:25:24

Mourni Tenchou
2019-05-20 04:28:10

Mourni Tenchou
2019-05-20 04:31:12

Alex Vee
2019-05-20 04:46:24

Mourni Tenchou
2019-05-20 04:51:15

Alex Vee
2019-05-20 05:14:03

Kljunaš Avstralski
2019-05-20 15:27:18


原文網址 Jeff Miller
2019-05-18 22:57:54

Hi - thanks for the add... first post here and day 2 with my photon. This latest print is clicking between layers... I can actually see the bed release and drop when the click occurs. Is that normal? It is a thick model at this point in the print.

翻譯年糕

Niggi Niklaus
2019-05-18 23:30:02

Will Koone
2019-05-19 01:33:06


原文網址 Todd Gullion
2019-05-17 03:54:14

Hello, i have a newbie to the photon question i cant seem to find on any forums. I just unboxed my photon and i am currently setting up the level, i do what it says and when the option to set z=0 appears it doesnt beep after i click yes. When i hit home again the home position is still higher. I know i am missing something. But i have tried doing the leveling just as many videos show. But it doesnt seem to take. Any help would be appreciated.

翻譯年糕

Richard Shapiro
2019-05-17 03:58:46

Todd Gullion
2019-05-17 03:59:11

Richard Shapiro
2019-05-17 04:00:04

Wesley Boynton
2019-05-17 04:01:57


原文網址 Ian Fiebig
2019-05-16 13:22:45

Replaced screen and glass protector, put in new FEP. Try #2 on third print, a week after try #1. BUT I hear the click of the FEP, so I think I'm good!

翻譯年糕

Richard Thomas
2019-05-16 15:15:52

Ian Fiebig
2019-05-17 00:28:53


原文網址 Dylan Lambert
2019-05-14 07:34:41

Houston, I think we have a problem... Isn’t there supposed to be a clip on that?

翻譯年糕

Eric Simmons
2019-05-14 07:48:00

Eric Simmons
2019-05-14 07:48:18

Dylan Lambert
2019-05-14 07:50:37

Jt Whissel
2019-05-14 07:53:33

Dylan Lambert
2019-05-14 07:59:31

Bob Martin
2019-05-14 08:00:13

Jt Whissel
2019-05-14 08:01:47

Jt Whissel
2019-05-14 08:02:55

Eric Simmons
2019-05-14 08:09:38

Dominick Trascritti
2019-05-14 08:09:40

Adam Brockmeier
2019-05-14 09:35:53

Juan Camilo Herrera
2019-05-15 05:33:03

Bob Martin
2019-05-15 06:43:56


原文網址 Joe Foulkes
2019-05-10 20:38:30

Need some help, just installed a new LCD, did an exposure test but I didn't get anything on the screen? ?

https://s.click.aliexpress.com/e/cCIJRna0

翻譯年糕

Juan Camilo Herrera
2019-05-10 20:41:40

Farryl Bird
2019-05-10 20:45:58

Joe Foulkes
2019-05-10 20:46:26

Regan Fairbanks
2019-05-10 20:47:54

Joe Foulkes
2019-05-10 20:59:16

Mario Reinh
2019-05-10 21:48:43

Joe Foulkes
2019-05-10 21:49:24

Mario Reinh
2019-05-10 21:51:06

Mario Reinh
2019-05-10 21:52:29

Vinicius Silva
2019-05-10 21:52:30

Joe Foulkes
2019-05-10 21:53:12

Joe Foulkes
2019-05-10 21:54:00

Mario Reinh
2019-05-10 21:54:05

Mario Reinh
2019-05-10 21:54:22

Joe Foulkes
2019-05-10 21:56:14

Mario Reinh
2019-05-10 22:00:00

Joe Foulkes
2019-05-10 22:03:18

Mario Reinh
2019-05-10 22:07:37

Joe Foulkes
2019-05-10 22:22:01

Milton Maxson
2019-05-10 22:28:39

Joe Foulkes
2019-05-10 22:37:58

Joe Foulkes
2019-05-10 22:38:03

Joe Foulkes
2019-05-10 22:38:04

Jake Larson
2019-05-10 22:55:01

Andrey Sabrev
2019-05-10 23:01:48

Joe Foulkes
2019-05-10 23:02:11

Andrey Sabrev
2019-05-10 23:03:38

Joe Foulkes
2019-05-10 23:04:26

Andrey Sabrev
2019-05-10 23:10:21

Andrey Sabrev
2019-05-10 23:11:24

Joe Foulkes
2019-05-10 23:12:09

Ondrashek Zátopek
2019-05-11 01:23:23

Ondrashek Zátopek
2019-05-11 01:24:22

Joe Foulkes
2019-05-11 01:26:34

Elvido Cataldo
2019-05-11 04:30:13

Joe Foulkes
2019-05-12 20:05:22

Andrey Sabrev
2019-05-12 22:49:23

Mark Schofield
2019-05-14 03:51:55


 

全不選 發文排行