Anycubic Photon Printer Owners 造訪社團 » LCD

原文網址 Enrico Oggero
2020-03-13 01:16:27

Hello folks!
Thanks a lot for many precious tips avilable here.

Conducting tests to improve printing size up to up to 1 mete r!
Since my Photon is under maintenance (dued to wobble issue), I'm conducting some test in order to discover real software potential.

I modified "__dlpconf_" file to following machineSize values (mm): X:68.04 Y:120.96 Z:1000
In simple terms I tried modify Photon printer profile in order to achieve printed piece up to 1 meter. Anycubic Photon Slicer V1.3 software allows slicing "oversized" STL model and I got *.photon file (2.8 Gb!).
After launching file print comes test failure : Printer lowers its platform to home (I manually simulate home to sensor) but printer keep lowering instead of printing. (Video shows test)
Printing progress goes from 1% to complete without any printing process. Do you think printer firmware (Photon 5.5, V4.2.3_LCD) allows "oversized" printing? In case answer is "NO" do you know about open source software I could install on printer allowing custom profiles?
Thank you all for reading and help! ? 翻譯年糕

Richard Humble
2020-03-13 02:37:54

Enrico Oggero
2020-03-13 03:09:02

Enrico Oggero
2020-03-13 03:27:19

原文網址 Allan Allison
2020-03-12 23:55:20

Need some help. Printer stopped printing but on the little screen it was still going as though it was still printing but the build plate was not moving. After removing the resin vat and taking the build plate off I turned off the printer removed my usb stick let it sit for about 10 mins. Turned the printer back on and tried to raise the build plate back to the top but it would not budge. Also ran a LCD screen test and nothing was showing up.

Any help would be greatly appreciated thanks

翻譯年糕

Benny Woolley
2020-03-12 23:56:32

Allan Allison
2020-03-12 23:59:39

Allan Allison
2020-03-13 00:01:04

Merv Hinton
2020-03-13 00:10:53

Merv Hinton
2020-03-13 00:12:50

Jim Fuqua
2020-03-13 01:50:59

Stephen Boulton
2020-03-13 02:10:51

Allan Allison
2020-03-13 04:45:22

Michael Earley
2020-03-13 10:05:19

Allan Allison
2020-03-13 10:19:32

Michael Earley
2020-03-13 10:26:12

Allan Allison
2020-03-13 10:30:37

Michael Earley
2020-03-14 01:18:45

Michael Earley
2020-03-14 01:19:01

Allan Allison
2020-03-14 01:59:42

Allan Allison
2020-03-14 05:25:29

原文網址 Stefano Reale
2020-03-12 18:13:24

BlueCast X5 for lcd printers. No postcuring, normal investment.

Rose Gold. Credits Opala Luís

Lcd印表機的bluecast x5. 沒有療程, 正常投資.

玫瑰金色. 感謝

· 查看原文 · 為此翻譯評分

Xavi Ferrer
2020-03-12 20:06:46

Ricardo Rivera Mellado
2020-03-12 21:28:56

Stefano Reale
2020-03-12 21:56:18

Stefano Reale
2020-03-12 21:57:22

Ricardo Rivera Mellado
2020-03-12 22:32:14

Игорь Лубенец
2020-03-12 22:37:01

Stefano Reale
2020-03-12 22:37:22

原文網址 Scott Comber
2020-03-12 09:07:47

Resin works violet lcd castable resin.

翻譯年糕

Sean Bauer
2020-03-12 09:20:42

Scott Comber
2020-03-12 09:28:49

Daniel Hoke
2020-03-12 09:34:27

Scott Comber
2020-03-12 09:41:54

Sal Jusufovic
2020-03-12 09:42:33

Scott Comber
2020-03-12 09:42:57

Daniel Hoke
2020-03-12 09:44:45

Scott Comber
2020-03-12 09:44:47

Nathan Carlos
2020-03-12 09:44:56

Scott Comber
2020-03-12 09:46:58

Jarrod Smith
2020-03-12 10:28:35

Scott Comber
2020-03-12 10:29:29

Jarrod Smith
2020-03-12 10:31:00

Daniel Hoke
2020-03-12 10:33:35

Dan Elent
2020-03-12 10:34:34

Scott Comber
2020-03-12 10:39:49

Dillon Whitaker
2020-03-12 10:45:34

Jason Dickson
2020-03-12 10:54:33

Ryan Neal
2020-03-12 10:57:12

Justin Berry
2020-03-12 11:15:49

Justin Berry
2020-03-12 11:16:16

Justin Berry
2020-03-12 11:18:19

Justin Berry
2020-03-12 11:19:40

Justin Berry
2020-03-12 11:21:17

Scott Comber
2020-03-12 11:23:12

Daniel Hoke
2020-03-12 11:23:55

Justin Berry
2020-03-12 11:24:19

Daniel Hoke
2020-03-12 11:26:41

Scott Comber
2020-03-12 11:29:55

Scott Comber
2020-03-12 11:35:42

Scott Comber
2020-03-12 11:37:51

Scott Comber
2020-03-12 11:40:02

Scott Comber
2020-03-12 11:40:20

Scott Comber
2020-03-12 11:47:04

Scott Comber
2020-03-12 11:47:24

Scott Comber
2020-03-12 11:48:47

Scott Comber
2020-03-12 11:53:06

Brandon Wolbers
2020-03-12 11:54:39

Justin Berry
2020-03-12 12:44:06

Scott Comber
2020-03-12 12:44:48

Justin Berry
2020-03-12 12:45:50

Carlos Villamar
2020-03-12 14:10:28

Chris Koonce
2020-03-12 14:26:09

Chris Koonce
2020-03-12 14:27:20

Brandon Wolbers
2020-03-12 14:46:14

Scott Comber
2020-03-12 15:01:47

Scott Comber
2020-03-12 15:22:53

Carlos Villamar
2020-03-12 15:41:37

Scott Comber
2020-03-12 16:22:29

Justin Berry
2020-03-12 20:45:58

Justin Berry
2020-03-12 20:47:17

Daniel Hoke
2020-03-12 21:15:59

Daniel Hoke
2020-03-12 21:20:01

Daniel Hoke
2020-03-12 21:24:43

Scott Comber
2020-03-12 21:26:38

Scott Comber
2020-03-12 21:27:24

Scott Comber
2020-03-12 21:28:15

Daniel Hoke
2020-03-12 21:31:30

Daniel Hoke
2020-03-12 21:33:21

Scott Comber
2020-03-12 21:40:37

Daniel Hoke
2020-03-12 21:41:58

Scott Comber
2020-03-13 05:05:36

Dillon Whitaker
2020-03-13 22:03:00

Scott Comber
2020-03-14 05:38:39

Dillon Whitaker
2020-03-14 05:54:22

原文網址 David Sea
2020-03-12 06:58:43

So, I've had to change 2 LCDs in under 2 weeks and I couldn't figure out why. Everything was leveled, resin strained every time, fep cleaned every time, etc.

I finally figured it out and wanted to let you guys know. I received some Siraya Fast grey resin that had some semi cured resin in it already, right out of the bottle. How did I figure this out? I strained the reain before it went into the vat and found it in the cleaned strainer.

Has anyone ever seen this?

翻譯年糕

Tobi Altebaeumer
2020-03-12 07:07:47

Jacob Hale
2020-03-12 07:28:22

David Sea
2020-03-12 07:33:41

David Sea
2020-03-12 07:34:13

Jacob Hale
2020-03-12 07:59:13

Keith Yinger
2020-03-12 23:19:04

David Sea
2020-03-12 23:23:57

David Sea
2020-03-12 23:25:15

Keith Yinger
2020-03-12 23:35:30

Justin Lincoln
2020-03-13 00:32:55

原文網址 Joseph Bochinski
2020-03-11 23:05:52

So I've run into a bit of a problem. I guess there was too much suction/adhesion between the FEP and the LCD screen while I tried to level using the flint reed method, but it caused the lcd screen to detach from base of the printer. I removed the vat and checked the screen, the cable is undamaged and running a UV test I still see light coming out correctly. However the glue or whatever is used to hold it in place has been compromised and now the screen is loose, is there a way I can reattach it without buying a new one? I briefly thought about using superglue or something, but then thought it'd be better to ask more experienced people.

Edit: added photos

所以我遇到了一點問題. 我猜我試圖用弗林特蘆葦方法平穩時, fep和lcd螢幕之間有太多的吸/粘合, 但它導致lcd螢幕從印表機底部分離. 我移除了增值稅並檢查螢幕, 電纜完好無損, 進行紫外線測試, 我仍然看到光亮正確. 但是膠水或任何用來保持它的東西已經被損壞了, 現在螢幕鬆散了, 有沒有辦法可以不買到新的嗎? 我曾短暫想過使用超級膠水之類的東西, 但後來覺得最好問問更有經驗的人.

編輯: 新增像片

· 查看原文 · 為此翻譯評分

Joeltron Bament
2020-03-11 23:07:42

Ronny Grudt
2020-03-11 23:10:12

Cody Cockayne
2020-03-11 23:12:01

Joseph Bochinski
2020-03-11 23:14:44

Adrian Carter
2020-03-11 23:18:18

Cody Cockayne
2020-03-11 23:19:34

Joseph Bochinski
2020-03-11 23:22:26

Cody Cockayne
2020-03-11 23:48:46

Rick Hanson
2020-03-12 00:24:17

Scott Pavlich
2020-03-12 03:55:58

Robert Mun
2020-03-12 20:08:29

Cody Cockayne
2020-03-12 23:19:18

Cody Cockayne
2020-03-12 23:20:20

Rick Hanson
2020-03-12 23:23:26

Jonathan Hall
2020-03-13 00:18:34

原文網址 Adam Huenecke
2020-03-11 21:27:35

Anyone have experience removing the LCD screen connection from the motherboard? Is it a vertical or horizontal pull to disconnect? I’m trying not to hulk the connection apart by doing this the wrong way...

翻譯年糕

Sean Latto
2020-03-11 21:32:06

Adam Huenecke
2020-03-11 21:34:52

原文網址 Matt Butler
2020-03-11 10:03:33

(Anycubic Photon Tools)

So I had to replace my screen. In doing so I accidentally knocked lose the ribbon to the build in control LCD screen of the photon. I have to get longer Metric T-Handle Hex Key Set tomorrow to be able to take the mother board out to to reset that wire properly.

Is there a place for this group that has a list for suggest tools and stuff to buy for working on the internal guts of your Anycubic Photon? Thanks in advance! ?

翻譯年糕

原文網址 Dean Eyre
2020-03-10 22:21:08

Help..I've just changed my lcd for a new one and now I'm getting Error code T-100, any ideas on what the problem is. It doesn't show the black rectangle either for the screen test.

翻譯年糕

Daniel Lemire
2020-03-10 22:24:24