Anycubic Photon Printer Owners 造訪社團 » Anycubic

Hi All!

Im having my first go at Hero Resin (white). I bought it for a specific use and model.

Im having trouble with “goopy” prints. Talking with Matt, we believe the exposure settings are good, but maybe I’m not supporting the model correctly or something. Ive printed it very cleanly with the same supports using Siraya Tech FAST (the gray print in the pics)

Anycubic OG Photon
0.05 layers
4 base layers
70sec base exp
15-17 sec layer exposure (I’ve tried all three)

It’s really hard to photograph the white, but I think you’ll see the defects in the photos.

Thanks in advance!

翻譯年糕

what do you think of this configuration that i found bun video for anycubic Gray? what does off time help with?

翻譯年糕

So i have finaly managed to get Anycubic to share with me a document of Their Clear Green resin examination report. According to this report resin is classified as medium hazard (two out of four grades possible). That already means - "handle with caucion".
STOT classifacation as "Category 3" (This category only includes narcotic effects (dizziness, drowsiness) and respiratory tract irritation (sore throat, cough). These effects, while adversely altering human function, are of short duration after exposure, and do not result in significant alterations of structure or function following recovery.) It is not deadly but this report as little data in it. All toxicological affects are stated as "NO DATA". And it doesnt contain any recomendations on ihale protection. Only eyes and skin protection. That is very strange because they state that Inale ma cause allergica irritation and cough (wich in many cases can be severe). In My opinion this report only gives us a clue about general harazrd amount resin contains and what it is made of.

I did my own brief reserch about resin contents:
Urethane Acrylate - is safe in finished form (hard cured or in not cuired form (doesnt meant you can drink it!). BUT if heated (required temperature stated as 100celcius) it starts to produce hazardous vapors of Fenol and Phormaldeghyde that can lead to chronic poisoning. Concidering required temperature it cannot be considered very hazardous (still not 100% safe).
Acrylate monomer - Experimental and clinical studies have documented that monomers may cause a wide range of adverse health effects such as irritation to skin, eyes, and mucous membranes, allergic dermatitis, stomatitis, asthma, neuropathy, disturbances of the central nervous system, liver toxicity, and fertility disturbances.
Photoinitiator - is believed to be toxic to aquatic organisms. Releases to the environment are to be avoided. Can cause skin and breating organs irritationa nad allergic reactions (same as other contens of resin)
Must remind you that allergy is underestimated. It can be a danger to your life. Please be carefull.

So to summ things up:
Resin is not deadly if inhaled by accident. Get to fresh air and rest if you feel dizzy.
People with breating problems (astma or anything close to it) must pay extra attention to proper breating protection (use respirator advised in my guide).
As all chemicals your reaction to them can be different. Some people can suffer headaches some can have high blood pressure allergy or god knows what else.. Some wont even notice anything. We are all different!
Be smart! Wear protection. Dont test your health for nothing. Consequences can be unpredictrable. Spend extra penny to protect your and your family's health. (get a raspirator, get a cabinet or any suction vent system.

PS this post is intended as educational and for precaution. Not to scare anyone from resin printing as some said.
Yes im readdy for your rotten tomatoes. Bring them on! ?

所以, 我終於找到任何立方體給我分享了一份他們清晰的綠色樹脂檢查報告的檔案. 根據這份報告, 樹脂被歸類為中等危險(可能的四個等級中有兩個). 這已經意味著". 處理caución ".
Stot分類為"第 3 類" (這一類僅包括麻醉效果(頭暈, 溺水)和呼吸道刺激(喉嚨痛, 咳嗽)). 這些影響雖然對人的功能產生負面影響, 但在曝光後是短暫的, 不會導致結構或功能的重大改變. 這不是致命的, 但這份報告中很少的資料. 所有毒理學影響都被描述為"沒有 資料", 而且它沒有包含任何關於ihale保護的回應. 只有眼睛和面板保護. 這很奇怪, 因為他們說inale ma會引起過敏和咳嗽(在許多情況下可能是嚴重的). 在我看來, 這份報告只給我們一個關於harazrd將軍含有的樹脂數量和它是由甚麼組成的線索.

我為樹脂內容做了短暫保留:
Urethane丙烯酸-成型安全(硬治癒或未治癒的形式(不代表你可以喝它!)! . 但是如果加熱(所需溫度為100攝氏度), 它開始產生可能導致慢性中毒的芬諾和phormaldeghyde的危險蒸汽. 調節所需溫度不能被視為非常危險(仍然不安全).
丙烯酸單體-實驗和臨床研究表明, 單體可能會對健康造成廣泛的不良影響, 如面板, 眼睛和粘膜, 過敏面板病, 胃炎, 哮喘, 神經系統神經系統的擾亂, 中樞神經系統 和生育擾亂.
光發起器-據信對水生生物有毒. 應避免向環境排放. 可能會導致面板和繁殖器官刺激nad過敏反應(與其他樹脂的抗力一樣)
一定提醒你過敏被低估了. 這可能對你的生命構成危險. 請小心.

所以總結一下:
如果意外吸入樹脂不是致命的. 如果你覺得頭暈, 呼吸新鮮空氣, 休息.
有繁殖問題的人(astma或任何接近它的東西)必須特別注意適當的繁殖保護(使用我的指南建議的呼吸器).
就像所有化學品一樣, 你對它們的反應可能不同. 有些人可能會頭痛, 有些人可能有高血壓過敏, 或者天知道還有甚麼.. 有些人甚至不會注意到任何事情. 我們都是不同的!
聰明點! 戴上防護. 不要白白測試你的健康. 後果可能無法預測. 花額外的錢來保護你和家人的健康. (得到一個raspiator, 得到一個櫃子或任何吸氣系統.)

Ps這個帖子是為了教育和預防. 不要像一些人所說的那樣嚇唬任何人.
是的, 我準備好了你的腐爛西紅柿. 讓他們來吧! ?

· 查看原文 · 為此翻譯評分

About green transparent resin from Anycubic - there is a time range for each layer from 3 seconds to 15 seconds. Have you ever tested such a short time for this?

翻譯年糕

Anybody having success with esun castable resin and anycubic Anybody having success with esun castable resin and anycubic 翻譯年糕

Guys, a technical question here. I noticed, that in many cases the part of my models facing away from the build plate has a kind of melted look, details look soft. I use Anycubic Skin, and based on the XP finde it's 10 seconds recommended as exposure time. Is it possible that those parts are overexposed?

翻譯年糕

Does anybody have any experience with a failed Z sensor. I'm already in contact with anycubic support, but I figured I'd see others experience here.
The problem manifested with the machine never remembering where zero is after leveling the bed. So the build plate drives straight into the lcd.

翻譯年糕

2nd & 3rd of four Elementals by Printed Obsession. 1440 Makers Brushfire Charity. Using anycubic3dprint Photon, SirayaTech Blu Clear, and lot's of washes and inks. (well not so much on the air elemental)
翻譯年糕

Just printed with the Anycubic Clear resin for the first time, and it came out gorgeous. However, after curing the otherwise glass-like model have developed a brownish-tint. Is this as to be expected with clear resin, or am I doing something wrong in my-post printing and curing process?

翻譯年糕

Of the 5 attempts I've done so far, 4 have only made a platter on the FEP, and the other broke free of the supports and adhered to the FEP. FEP is tight and sounds like a drum, I've tried both the paper bed leveling and the flint read method of bed leveling. Attempts so far are with Anycubic Orange resin. What else should I attempt, what am I missing here?

翻譯年糕