Anycubic Photon Printer Owners 造訪社團 » mac

I have been printing with Anycubic Green since I got my machine. I have a Liter of Elegoo Grey that I want to try out. This is my first time trying anything other than the green. Do these settings look right? The spread sheet says "Off Time" is 6,5. Not exactly sure what that means. Is that the Light off Delay and Bottom Light off? And what does 6,5 mean?

翻譯年糕

My first prints! Turned out pretty good. Had a slight issue with supports with one. But I think 8s per layer should have been 10s. .03 layers. Cleaned in ultrasonic cleaner with Mr. Clean. Not fully cured yet. Overall very pleased with the machine!

翻譯年糕

I love this machine ? .
This is one of my best prints for sure, and one of my few resin prints since I own this printer for a little more than one week.
The prints came out straight from the printer like this, I just removed the supports and fixed a little defect (because a support fused with a model area) using a drop of resin and sanding paper. I still have to remove all the supports marks (that are few and easy to clean) and paint them.

翻譯年糕

Some of you may know how much I said how great and happy I was with the Anycubic Photon S :) And I was whilst it worked I now turn to you again for help.

I bought a Photon from Ali Express, new from their official store in March, it worked for about 3 months and then I encountered a problem where it would stop printing at random points during a print, I contacted Anycubic tech support did all the tests they asked of me and evnetually they sent me a new mainboard which I thought was very fast.

It has now been weeks since I got the new mainboard and each step forwards I take something else seems to arise as a problem, this is the list so far, it still stops randomly when printing, it now gets so hot it vapourises the resin ( I believe this to be very dangerous, and also as in the image there is an issue with the light.

My worst fears came true as today I recived this message from tech support

"I have tried to apply for a change of machine to the store manager, but unfortunately failed."

Which I am assuming if they cant help me it means tough :(

Any help is massivly appreciated :)

*Updated* with new image. I am now aware that basically if I cannot get the printer to work "tough luck we got your money" :)

So far, as fast and good the tech supprt has been, none of my problems have been fixed in fact I am encoutntering more problems as I attempt to carry out their instructions.

翻譯年糕

A small project I am working on.
A friend gave me a present, the C3PO and R2D2 figures of the Imperial Assault game. I have designed in Fusion 360 the part of the door of the scape pod to put them in situation ?
Eelegoo Gray.
With Photomn Classic. I love this machine. The small details are amazing.

翻譯年糕

Some orcs i sculpted, bike by karnageking. Printed on epax since my photon is down, need to get it working again. Love these machines. Waaagh! :p

翻譯年糕

Hi there! Thanks for accepting me into the group. These are my very first two prints and I'm impressed by the ease of use of this machine... I've just started this trip into the world of SLA printing so I'm looking forward to your advices.

I just saw some videos about how the Mr. Clean and equivalent liquids were better than IPA to remove resin residues... Gotta try that...

翻譯年糕

Anyone seen this yet?

US $314.50 15%OFF | 2019 Newest Wash Curing Machine Light Curing 3D Printer dedicated Processing Curing Cleaning Two In One

翻譯年糕

Well. I had a day off on Monday. I finally took apart my Photon to put in a third screen. Thankfully it came apart fine.

But why is this machine so damned hard to install things in?

The four screws that hold the case go into these little troughs so if you can't get the screws back all the way to the other part with an allen key (provided) it falls into the trough and is nearly impossible to retrieve.

To put the screen in, I slid the ribbon into the slot on the red flat table, and of course it doesn't just go down to where it's needed, it has to be pushed over a wall so the ribbon can reach the connector. Which you may not know until it becomes harder to do.

Removing the UV pyramid is equally frustrating as the other screws. The allen key provided is JUST long enough to remove the back two screws, but not long enough to ensure they get to go back in easily.

Putting the unit back together is incredibly frustrating as the bottom doesn't align easily to the sides, and you have to get those screws in perfectly through two holes to the body, without losing them in the interior again.

But dammit, with some incredibly sticky double-sided tape, I managed to get the new screen in.

My FEP was really cruddy so I replaced that. Luckily the video Anycubic provides on YouTube is amazing. It worked like a charm. The tightness of the FEP using that Coke bottle cap is amazing. Like it was done professionally.

I did a new print in Anycubic Green and it failed. Dammit! I haven't had a successful print on this thing for over a year.

So I found it may have been a corrupt file.

I put a different file on the bed that was NOT corrupt, and ...

IT WORKED!!!

I mean it printed really nice!

Today I used my first bit of Monocure Clear and it printed! PROPERLY!

Ok... I may be back...

翻譯年糕

Question:
So I’ve been looking at what you awesome people do for washing and curing and am curious who uses machines to wash and cure vs who uses tub and does it by hand for washing (curing usually by uv but some have said they use the Suns uv)

翻譯年糕