Anycubic Photon Printer Owners 造訪社團 » EX

原文網址 Jayson Stewart
2020-03-07 21:27:34

Anyone use windex to clean their FEP? How did it fair?

翻譯年糕

Pikie Perch Poacher Sidious
2020-03-07 21:29:23

Shane Rozzell
2020-03-07 21:31:23

Jeff Surma Jr.
2020-03-07 21:36:29

Jonathan Andersson
2020-03-07 21:38:45

Jim Nelson
2020-03-07 21:40:59

Brett Isaacs
2020-03-07 21:53:37

John Smith
2020-03-07 22:05:42

Lou Steinritz
2020-03-07 22:10:04

Gregore Conn
2020-03-07 22:15:57

John Henry
2020-03-07 22:55:33

Paul Songer
2020-03-07 22:56:29

John Henry
2020-03-07 22:57:00

Jonathon Michael Starwalt
2020-03-08 00:24:55

Gary Slovinsky
2020-03-08 01:00:53

Arthur White
2020-03-08 01:45:52

John Smith
2020-03-08 07:18:22

Aaron Strome
2020-03-08 07:26:54

Aaron Strome
2020-03-08 07:27:34

Lance Turner
2020-03-09 00:25:22

原文網址 Robert Small
2020-03-07 18:20:46

One of the reasons it's important to understand 3D modeling in the programming that does it is when you're slicing or file sometimes the normals in the 3D model were flipped in short it means no light is bouncing off of that surface that is the program cannot calculate light bouncing off of that surface. And for some reason that affects the slicer into thinking that that surface does not exist. To fix it one has to go into the 3D program that built the model oral program that can manipulate the model such as blender and find those faces and flip the normal if in the 3D program you can see the faces they should turn black or if they word black to begin with and you flipped their normals then they will be lit up. Basically the opposite state.

翻譯年糕

Brett Isaacs
2020-03-07 22:01:47

Robert Small
2020-03-07 23:23:56

Brett Isaacs
2020-03-08 01:02:42

原文網址 Jayson Stewart
2020-03-07 16:48:41

Any insight on what happened here? I printed 2 batches rupees. The first batch turned out great but the second batch had air bubbles inside the print and one rupee adhered to the FEP half way thru the job. I had 8 bottom layers at 90 sec. Exposure with 8 second exposure for the subsuquent layers and 4 second pause after each layer.

翻譯年糕

Richard Humble
2020-03-07 16:54:01

Per Bekker-Madsen
2020-03-07 17:02:00

Jayson Stewart
2020-03-07 19:19:30

原文網址 Alex Bainbridge
2020-03-07 14:31:52

Finally got good adhesion with the help of re levelling and warming the goo before hand ?

What’s occurred here? This was on the closest corner to the bed, it was auto orientated and supported at bout 70-80% had a few more pieces on the plate but they came out as expected. Guess I could sand it to make it less noticeable?

翻譯年糕

Marty Khull
2020-03-07 14:52:04

Alex Bainbridge
2020-03-07 14:56:43

Alex Bainbridge
2020-03-07 15:16:09

Marty Khull
2020-03-07 15:30:04

Scott Pavlich
2020-03-07 15:52:39

Alex Bainbridge
2020-03-07 16:29:57

Alex Bainbridge
2020-03-07 16:32:51

原文網址 Cameron Lee Johnson
2020-03-07 14:31:06

So i had my first failure. I was printing a large piece of a display model (a little smaller than a baseball) and then super tiny versions of that model as well.

They all broke off the supports. Since this was my first time using opaque resin, im assuming its under exposure? Or would the supports have failed as well? What interesting is i had 2 sets of the smaller model pieces. You can see the base layers of one on the plate there. But the other has nothing

Anycubic black
4 base layers at 75 seconds.
.05 layer height at 8 seconds

翻譯年糕

Scott Pavlich
2020-03-07 15:09:32

Jesper Hvid
2020-03-07 15:47:22

原文網址 Josh Dalgliesh
2020-03-07 14:14:25

So I've noticed that there seems to be a lot of newcomers of late (myself included). Just came across a video that consolidates a lot of good modelers and thought to myself that this video would have definitely been a good starting point/helpful for find minis that are perfect for me had I not already found them. So if you're wondering what to print next, I hope this year old video helps :)
https://www.youtube.com/watch?v=pbcw-wce6uA 翻譯年糕

原文網址 Jacob William Curtis
2020-03-07 14:00:59

Hey Folks,

I'm having some prints come out slightly deformed. do I need more supports for the lowest points? I tried increasing exposure time with this resin to slightly above the recommendations, and the room I'm printing in is about 70F.

翻譯年糕

Scott Pavlich
2020-03-07 15:50:35

原文網址 Mata Mac Gille Fhionntain
2020-03-07 12:56:09

What things am I considering when doing a print in place/flexi item like the Trilobite posted earlier. Not that specific one, but there are some I would like to print like this one......

翻譯年糕

Mikel Deiman
2020-03-07 21:23:00

Mata Mac Gille Fhionntain
2020-03-08 02:51:29

Mikel Deiman
2020-03-08 02:53:16

Mata Mac Gille Fhionntain
2020-03-08 02:55:20

原文網址 Mika Gruszka
2020-03-07 11:32:29

Loving these flexi trilobite critters! They are so fun and take barely any resin!

Also: anybody got any suggestions for a dice tower that isn't too big for the photon? All the ones I'm finding are too big and I don't want to resize them.

https://www.thingiverse.com/thing:3839472

翻譯年糕