Anycubic Photon Printer Owners 造訪社團 » UV

原文網址 Steve Richardson
2020-01-13 03:41:13

Anyone have setting for Anycubic Eco UV Resin Grey they could share....this stuff is kicking my butt. Can't seem to get print to hand on the supports. This stuff flexes a lot and seem to just break off. Same model I have successfully printed in standard green.

翻譯年糕

Karoten Buford
2020-01-13 03:42:55

Steve Richardson
2020-01-13 03:50:24

Johnny Grant
2020-01-13 03:53:11

Grant Kinnick Smith
2020-01-13 04:09:07

Grant Kinnick Smith
2020-01-13 04:10:26

Grant Kinnick Smith
2020-01-13 04:11:14

Chris Holden
2020-01-13 04:55:08

Nick Robinson
2020-01-13 06:08:49

Chris Holden
2020-01-13 07:56:26

Ben Brooks
2020-01-13 11:51:43

Edward Hill
2020-01-13 21:27:27

Edward Hill
2020-01-13 21:28:53

Mike Schuster
2020-01-14 01:58:24

Steve Richardson
2020-01-14 01:58:37

原文網址 Cheng Yeoh
2020-01-11 01:51:57

Hi all, I’ve been printing some 20mm calibration XYZ cubes. I’m using elegoo grey (normal £35/litre stuff from amazon). I’m curing in a 36 w (4x9w UV) nail curer for 40-60 minutes (turning halfway). Slicing in Chitubox.

50u at 8 seconds gives 20.2 in the xy and 20.1mm in the Z.

I thought the resins were meant to shrink by 7% according to spec sheets - this has grown? The prints feel smooth and not tacky - they’ve been curing for quite a while - do I need more? Or is still quite a stable resin despite the manufacturers figures of 7%? Thanks!

翻譯年糕

Alvydas Jatkialo
2020-01-11 02:11:25

Cheng Yeoh
2020-01-11 02:35:56

Alvydas Jatkialo
2020-01-11 05:35:53

Cheng Yeoh
2020-01-11 06:53:41

Alvydas Jatkialo
2020-01-11 07:20:06

原文網址 Дамян Методиев
2020-01-11 01:36:37

I found cheap glasses with UV protection.

翻譯年糕

Richard Humble
2020-01-13 14:19:43

Дамян Методиев
2020-01-13 15:05:34

原文網址 Mihnea Stoica
2020-01-11 00:24:21

I have noticed this uv light under the machine. Is it normal? I've had the printer for at least a month now and it.s my first time seeing it.

翻譯年糕

Hector Alvarez
2020-01-11 00:25:50

Mark Reynolds
2020-01-11 00:39:08

原文網址 Kevin Goethals
2020-01-10 15:57:40

Hey people! Most of my prints are coming out perfectly.
After printing I put them for 1-3 minutes in methanol alcohol, in a jar which I constantly shake during this time. Afterwards I put it in a UV spotlight on a 360 turning disk. However, I seem to get a lot of random white spots on my prints. They feel different then other print surfaces, they look like the color was scratched off, but u didn’t touch it, especially not in some small areas hard to reach...
I tried raising the lamp time while printing but that didn’t seem to resolve the issue.
Does anyone have a solution for this?

翻譯年糕

Kevin Goethals
2020-01-10 15:59:48

John Chrapkowski
2020-01-10 16:01:51

John Chrapkowski
2020-01-10 16:02:04

John Chrapkowski
2020-01-10 16:02:16

Sander Freitas
2020-01-10 16:17:31

Vincent Balmont
2020-01-10 16:48:17

Sander Freitas
2020-01-10 16:49:04

Vincent Balmont
2020-01-10 16:54:50

Sander Freitas
2020-01-10 16:55:30

Vincent Balmont
2020-01-10 17:05:28

Alex Vee
2020-01-10 17:09:44

Kevin Goethals
2020-01-10 17:11:27

Kevin Goethals
2020-01-10 17:12:39

Alex Vee
2020-01-10 17:13:48

Sander Freitas
2020-01-10 17:14:40

Kevin Goethals
2020-01-10 17:15:01

Fred Bey
2020-01-10 17:15:21

Ted Ukted Crunkhorn
2020-01-10 17:24:10

Fred Bey
2020-01-10 17:24:54

Simon Dyer
2020-01-10 18:42:13

Simon Dyer
2020-01-10 18:52:21

Shawn O'Hara
2020-01-10 21:24:52

Shawn O'Hara
2020-01-10 21:26:08

Shawn O'Hara
2020-01-10 21:29:14

Kevin Goethals
2020-01-10 21:30:31

Shawn O'Hara
2020-01-10 21:31:20

Gary Carone
2020-01-10 21:38:05

Alex Vee
2020-01-10 21:38:21

Alex Vee
2020-01-10 21:39:09

Simon Dyer
2020-01-11 04:38:16

Alex Vee
2020-01-11 05:59:26

Simon Dyer
2020-01-11 06:14:24

原文網址 Daniel WarChan Ward
2020-01-10 12:23:26

trying to get some uv led lights, would these be ok? https://www.ebay.com.au/itm/5M-UV-3528-SMD-Purple-Blacklight-300-LED-Strip-Light-Waterproof-12V-Power-Supply/223716381439 翻譯年糕

Andrew Glover
2020-01-10 14:00:06

Daniel WarChan Ward
2020-01-10 14:07:06

Bob Deblier
2020-01-10 16:52:54

原文網址 Brian JH
2020-01-10 10:32:52

Looking for some opinion; anycubic Photon. I just started using Siraya Tach blue and started having some weird failures in the middle of my prints. The rafts are fine, but it looks like the supports are just giving up. The lcd UV detection test pattern looks fine... what would cause supports of all sizes to just not print in the middle but work just fine everywhere else?

I’m confident my plate is level. Lift and retracts speeds are low. Level exposure time is 12 sec.

Update; looks like the FEP was too loose. I tightened it down and came out with a perfect print.

翻譯年糕

Sander van Deijl
2020-01-10 15:43:51

Brian JH
2020-01-10 22:24:36

Sander van Deijl
2020-01-10 22:33:55

原文網址 Keith Madeira
2020-01-10 09:16:35

Question...

My first printer arrived today and i was thinking of setting it up in my living room. Thing is I have a marine aquarium in there which uses UV as part of its lighting spectrum. Will this affect the prints? Question...

My first printer arrived today and i was thinking of setting it up in my living room. Thing is I have a marine aquarium in there which uses UV as part of its lighting spectrum. Will this affect the prints? 翻譯年糕

James Edward
2020-01-10 09:19:30

Jorge Salazar
2020-01-10 09:20:02

Richard Humble
2020-01-10 09:32:11

Shawn McDonald
2020-01-10 09:59:40

Nick Walker
2020-01-10 10:49:11

Melecio Guzman
2020-01-10 12:09:48

Jake Campos
2020-01-10 12:13:57

Bob Deblier
2020-01-10 14:09:29

Bob Deblier
2020-01-10 14:11:27

Bob Deblier
2020-01-10 14:12:39

Nick Walker
2020-01-10 14:49:57

Nick Walker
2020-01-10 14:50:41

Nick Walker
2020-01-10 14:53:30

Nick Walker
2020-01-10 15:01:57

Richard Humble
2020-01-10 15:31:21

Nick Walker
2020-01-10 15:48:20

Mikko Asikainen
2020-01-10 16:29:23

Niall Forrester
2020-01-10 18:37:55

Stephen Brewer
2020-01-10 19:53:46

Stephen Brewer
2020-01-10 19:55:49

Bob Deblier
2020-01-10 19:57:26

Bob Deblier
2020-01-10 20:02:26

Andrew Draffin
2020-01-10 21:27:24

Melecio Guzman
2020-01-10 23:23:48

Tiernan Messmer
2020-01-10 23:27:06

Melecio Guzman
2020-01-10 23:29:05

Brian J Anderson
2020-01-11 03:41:22

Jarin Udom
2020-01-11 04:50:23

Herman Simpson
2020-01-11 05:03:58

Bob Deblier
2020-01-11 05:10:55

Stefan Giudici
2020-01-11 05:13:42

Peter Teal
2020-01-11 05:17:33

Melecio Guzman
2020-01-11 06:19:11

Brian J Anderson
2020-01-11 06:23:56

Melecio Guzman
2020-01-11 06:37:35

Jason Archuleta
2020-01-11 06:39:24

Jason Francisco
2020-01-11 20:41:15

Keith Madeira
2020-01-11 21:35:32

Jason Francisco
2020-01-11 22:55:36

Joel Reid
2020-01-12 12:11:13

Jason Francisco
2020-01-13 16:36:20

原文網址 Jonathon Michael Starwalt
2020-01-10 09:11:09

Quick question:

When using a foil lined box and UV light for curing, how much should I adjust curing time? For example, I found a recommended curing time for Anycubic translucent green as 30 minutes, so should I give it 30 minutes in a foil box with a rotating stand, or should I cut that by half or some other ratio?

翻譯年糕

Ryan LaBarre
2020-01-10 09:42:16

Bob Deblier
2020-01-10 14:16:51

Jonathon Michael Starwalt
2020-01-11 07:45:02

原文網址 Tu Truong
2020-01-10 06:42:06

Hi All,

I've just started printing out large models that are hollowed out. I'm afraid of not being able to cure the inside of the models. What technique are people using to cure the inside of a model?

I was looking for a very slim UV string light that I could slide into the drain hole, but I wasn't sure if the flat LEDs would fit inside the model.

What are you guys doing?

翻譯年糕

Jarvis Läkemäker
2020-01-10 06:45:38

Joseph Wright
2020-01-10 06:46:40

Jacob Palmer
2020-01-10 06:47:06

William Preston Welch
2020-01-10 06:54:27

Stefan Giudici
2020-01-10 06:55:36

全不選發文排行