Anycubic Photon Printer Owners 造訪社團 » 螢幕

Hi, I got my photon zero two days ago and cant get the slicing software to open at all, it just wont go past the initialising screen which only stays up for a few seconds then nothing happens. Obviously with the Zero having a different extension to other printers its going to be really hard to get it to work without the software. I have downloaded the file from the Anycubic site and the same thing happens, not sure if my pc is to powerful (windows 10, 8gb, 1gb graphics card), but I am at a lose as I can only print the test file that came with the machine.

I have the latest version of Cura but that doesnt seem to have a setting for the Photon Zero and likewise have downloaded Z Suite.

can anyone help at all

嗨, 兩天前我得到了我的光子零, 而且根本無法開啟切片軟體, 它只是不會通過初始化螢幕, 它只停留幾秒鐘, 然後甚麼也沒發生. 很明顯, 零與其他印表機有不同的擴展, 沒有軟體, 很難讓它運作. 我從anycubic網站下載了檔案, 同樣的事情發生, 不確定我的電腦是否強大(windows 10 gb, 8 gb, 1 gb圖形卡), 但我在輸了 只能列印與機器一起的測試檔案.

我有最新版本的cura, 但似乎沒有光子零的設定, 也下載了z套件.

有人能幫忙嗎

· 查看原文 · 為此翻譯評分

I've noticed I now am getting z wobble after replacing my screen. Anyone know how to fix other than modding my photon? I've noticed I now am getting z wobble after replacing my screen. Anyone know how to fix other than modding my photon?

我注意到更換螢幕後, 我現在開始搖晃. 除了我的光子, 有人知道如何修好其他方法嗎?

· 為此翻譯評分

First print after replacing my photons busted screen with one for an Elegoo Mars. Unfortunately my ac black and st tenacious was off and made the thinner parts too soft. So her ears tore while removing supports.

用一個elegoo火星取代我的光子壞了的螢幕後, 第一個列印. 遺憾的是, 我的ac黑色和st tenacious關閉了, 使瘦部分變得太柔軟. 所以她的耳朵在移除支撐的時候撕裂了.

· 查看原文 · 為此翻譯評分

New screen, new fep, screen sealed with kapton tape, and the sweet pop of the print pulling away from the film. I would say this first time screen replacement is a success. Now to wait and see how it turns out

新螢幕, 新的fep, 用kapton膠帶封印的螢幕, 以及從影片中提取的甜蜜的流行音樂. 我會說, 第一次更換螢幕是成功的. 現在等待, 看看結果如何

· 查看原文 · 為此翻譯評分

This maybe a stupid question...can you get dodgy bottles of resin?
I have a bottle of grey and black anycubic and a bottle of elegoo clear blue. All recommendations the same 60/8 seconds. This is what I have set out to in the slicer. was using the Anycubic grey and getting great results (pic 1). I then switched to the black Anycubic (same settings) to print a simple base for a model. I've tried upright, 45 degrees, flat, all raised on supports etc but 5 failed prints. Either supports breaking, not sticking to build plate, but mostly resin forming on the FEP which I've had to empty and peel off (pic 2 and 3).
I thought it was the screen so swapped to translucent blue, exactly the same settings, could see the screen working through the resin , and it printed a random print perfectly first go (last pics) ?‍♂️ what's going on with this black resin?

這可能是個愚蠢的問題... 你能得到一瓶樹脂嗎?
我有一瓶灰色和黑色的任何立方體和一瓶elegoo清白藍色. 所有推薦的60/8秒. 這就是我在切片中闡述的. 使用任何立方體灰色, 獲得了很好的結果(圖片1), 然後切換到黑色anycubic (相同的設定)列印一個簡單的模型基礎. 我嘗試了直立, 45度, 平坦, 全都在支撐上, 但5個失敗的指紋. 要麼支援破碎, 而不是堅持構建板塊, 但主要是在我不得不清空和剝離的fep上形成樹脂(圖片2和3).
我以為是螢幕換成半透明藍色, 完全相同的設定, 可以看到螢幕通過樹脂工作, 然後隨機列印了一個完美的列印(最後一張照片) ♂️ 這黑色怎麼了 樹脂?

· 查看原文 · 為此翻譯評分

What double sided tape tape is recommended when replacing the lcd? Need to know asap. Got a screen arriving tuesday What double sided tape tape is recommended when replacing the lcd? Need to know asap. Got a screen arriving tuesday

更換液晶顯示器時, 推薦哪些雙面磁帶? 需要盡快知道. 週二拿到了一個螢幕

· 為此翻譯評分

Hey there, I've a problem with my Photon S' screen. Basically sometime I had printing issues and then I noticed that the screen wasn't working properly, so I opened the printer, plugged and replugged and secured the camble, it worked well for just the first print, then the issue came back.
What is weird is that sometimes it works well and some other times it makes all these stripes, for example now it just stopped making this bug (after few times of restarting and unplugging the USB) so I launched a print because if o don't restart the printer it continues working well), but I know it could restart bugging again at the next restart.
So what is the problem? The screen or the mother board? Because I already bought a new screen thinking it's the problem, but now I'm not 100% sure about that.
Thanks for the attention.

嘿, 我的光子螢幕有問題. 基本上有時候我遇到列印問題, 然後我注意到螢幕沒有正常運作, 所以開啟印表機, 插頭, 重新插頭, 保護了camble, 它效果很好, 然後問題又回來了.
奇怪的是, 有時候它運作良好, 有些時候它讓所有這些條紋, 比如現在它只是停止製作這個錯誤(幾次重新啟動和拔除usb), 所以我就啓動了一個列印, 因為如果o不重新啟動 印表機繼續運作良好), 但我知道它可能會在下次重新啓動時重新開始竊聽.
那麼, 有甚麼問題? 螢幕還是母板? 因為我已經買了一個新的螢幕, 認為這是問題, 但現在我不確定.
感謝大家的關注.

· 查看原文 · 為此翻譯評分

So I've run into a bit of a problem. I guess there was too much suction/adhesion between the FEP and the LCD screen while I tried to level using the flint reed method, but it caused the lcd screen to detach from base of the printer. I removed the vat and checked the screen, the cable is undamaged and running a UV test I still see light coming out correctly. However the glue or whatever is used to hold it in place has been compromised and now the screen is loose, is there a way I can reattach it without buying a new one? I briefly thought about using superglue or something, but then thought it'd be better to ask more experienced people.

Edit: added photos

所以我遇到了一點問題. 我猜我試圖用弗林特蘆葦方法平穩時, fep和lcd螢幕之間有太多的吸/粘合, 但它導致lcd螢幕從印表機底部分離. 我移除了增值稅並檢查螢幕, 電纜完好無損, 進行紫外線測試, 我仍然看到光亮正確. 但是膠水或任何用來保持它的東西已經被損壞了, 現在螢幕鬆散了, 有沒有辦法可以不買到新的嗎? 我曾短暫想過使用超級膠水之類的東西, 但後來覺得最好問問更有經驗的人.

編輯: 新增像片

· 查看原文 · 為此翻譯評分

So now that I owned resin printers for 18 months now I have some info for you all.
After 1000 hrs on the Photon S screen replacement and one going at 2000 hrs and still going. What I did when they came in was I looked at the whole machine all sides and such. And tried an experiment. There is a large fan on the bottom of these machines as well as Egeloo mars and others. They all have feet that raise the unit up about 1 inch at most. So I decided to raise one Mars and then One Photon I cut a hole below the unit into my stand/platform where the fan/unit would be above. This created better air flow and I have found that machine runs less hot and the lcd lasted longer up to 2x as much. So I would say Rasie Your Machines off the platform you have it on. See photos below on my test units. I have 8 Photons and 4 Mars machines and s400s and Phenom and Transform machines here as well.
Good luck and Happy Printing.
Michael LR3D

所以現在我擁有樹脂印表機18個月, 現在我有一些資訊告訴大家.
1000小時後, 光子s螢幕更換, 一個在2000小時後, 仍在進行中. 他們進來的時候我所做的是我看著整個機器的各個方面等等. 嘗試了一個實驗. 這些機器的底部有一個大粉絲, 還有egeloo火星和其他人. 他們都有腳能讓單元提高了大約1英吋. 所以我決定舉起一顆火星, 然後一個光子, 我在單位下面切了一個洞進入我的站台/平台上的球迷/平台. 這創造了更好的空氣流動, 我發現機器運行更少, 液晶顯示器持續更長至2倍. 所以, 我想說rasie你的機器離開了平台. 在我的測試單元檢視下面的照片. 我這裡還有8個光子和4個火星機器, s400s和phenom和變形機.
祝你好運, 印刷快樂.
邁克爾· l3d

· 查看原文 · 為此翻譯評分

Looks like the film got pierced, leaving cured black resin on the screen. Have scraped some of it off (with meths to soften it). Oddly the printer had reset the Home default for the plate-arm-thing, so had to reset it and stop the grinding noise.
Vale printer. I think you are well dead! :(

看起來電影被刺穿了, 把治癒的黑色樹脂放在螢幕上. 已經刮了一些(用冰毒來柔軟). 奇怪的是印表機重置了盤子臂裝置的預設, 所以不得不重置它並停止磨損噪音.
Vale印表機. 我覺得你已經死了! :(

· 查看原文 · 為此翻譯評分