Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Tom Barnes
2020-01-29 04:36:00

Uuuh wut.
Print came out fine, but obviously can't have this.
I assume it's just a bed level issue, just got to find out where it's not right, I'm thinking that the beds tilted slightly back and to the left as I have had this happen a few times and it's been a bigger problem nearer the front and in the right of the build plate

翻譯年糕

James Cachia-Garrett
2020-01-29 04:42:26

Tom Barnes
2020-01-29 04:49:46

James Cachia-Garrett
2020-01-29 04:57:22

原文網址 Tom Barnes
2019-10-14 07:50:41

Any thoughts as to why the skirt has peeled off the build plate like this?

翻譯年糕

Hector Alvarez
2019-10-14 07:57:20

Jesper Hvid
2019-10-14 07:58:41

Chris D'Andrea
2019-10-14 08:03:39

Steven Raybell
2019-10-14 08:05:34

Jlee Usn
2019-10-14 08:23:15

Steven Raybell
2019-10-14 08:24:37

Mark Wardle
2019-10-14 08:29:45

Nathan Kopp
2019-10-14 09:04:35

Mark Wardle
2019-10-14 09:13:46

Kyle Calderwood
2019-10-14 09:29:50

Mark Wardle
2019-10-14 09:32:06

David Retske
2019-10-14 10:30:25

Mark Wardle
2019-10-14 10:52:04

Dave Corbett
2019-10-14 11:01:40

David Bartholomew
2019-10-14 11:29:29

David Bartholomew
2019-10-14 11:30:39

Mike Roof
2019-10-14 12:20:16

Kyle Calderwood
2019-10-14 15:48:07

Tom Barnes
2019-10-14 16:29:10

Tom Barnes
2019-10-14 16:31:49

Phillip Kenney
2019-10-14 23:42:14

原文網址 Tom Barnes
2019-10-14 01:47:45

So I have a ultrasonic cleaner with quite a bit of excess uncured resin in it, what's the best way to dispose of it, as prints are not cleaning now, definitely need to replace the water/washing up liquid mix.

翻譯年糕

Evan Boone
2019-10-14 01:59:46

Tom Barnes
2019-10-14 02:01:32

Evan Boone
2019-10-14 02:02:32

Frank Jakobsen
2019-10-14 02:18:50

Stefan Giudici
2019-10-14 06:21:04

原文網址 Tom Barnes
2019-10-12 07:38:57

So the mech I posted about earlier sorta printed, printed this section then fell off the build plate and it got stuck to the fep? Took a little bit of pressure to take it off the fep.

I'm thinking the initial layer settings need to be higher, more time spent on the initial layers and maybe a few more of them?

Tia

翻譯年糕

Joseph Daniels
2019-10-12 07:40:22

Danny Lloyd
2019-10-12 07:49:33

Cliff Wiles
2019-10-12 15:19:52

原文網址 Tom Barnes
2019-10-12 00:10:46

still learning any trying to be more confident with supports but how on earth am I going to do this?

翻譯年糕

Allan Allison
2019-10-12 00:13:01

Tom Barnes
2019-10-12 00:13:56

Allan Allison
2019-10-12 00:14:31

Mike Armijo
2019-10-12 00:18:14

Bronson Ferri
2019-10-12 00:21:31

Shreyo Bagchee
2019-10-12 00:22:34

Cliff Wiles
2019-10-12 00:25:33

James Ogre Tate
2019-10-12 00:28:29

Miguel Angel Martinez Escalante
2019-10-12 00:29:59

James Ogre Tate
2019-10-12 00:33:31

Christopher Milnes
2019-10-12 00:39:24

Gary Houser
2019-10-12 01:00:58

Alexx Butnotalex
2019-10-12 01:52:06

Chad Elstad
2019-10-12 03:01:29

Tom Barnes
2019-10-12 07:11:53

Tom Barnes
2019-10-12 07:11:59

原文網址 Tom Barnes
2019-10-04 02:15:27

Hive mind, does a raft increase the chances of the print being successful, or is it just a waste of resin?

翻譯年糕

Nick Williams
2019-10-04 02:25:35

Alex Vee
2019-10-04 02:28:50

Mark Wardle
2019-10-04 02:29:33

Kyle Urban
2019-10-04 02:30:13

Vinicius Silva
2019-10-04 02:36:31

Jarrod Smith
2019-10-04 03:09:56

Michael Maxwell
2019-10-04 06:29:37

Sen Kun
2019-10-04 08:18:57

Chad Elstad
2019-10-05 11:28:04

Ivan Antharon Antalec
2019-10-06 06:29:29

原文網址 Tom Barnes
2019-10-04 01:08:59

still trying to get my head around this printer, just tried to print this (see image) and it failed, did the raft and that was it, not enough supports? supports not manly enough, too close together? I have seen people printing very close together and getting successes, what am I doing wrong.

翻譯年糕