Anycubic Photon Printer Owners 造訪社團

Recently I've posted here about an issue with Chitubox displaying nothing in place of a buildplate, like on screenshot below.

Tried all of your helpful suggestions, yet failed miserably.

Today I've found out that removing folder at %userprofile%\AppData\Local\ChiTuBox

solves the issue, also removing all profiles.

So, making backup is a must, but the issue is solved!

翻譯年糕

Hey everyone, I have encountered a issue with my Photon that I can't seem to find a solution for around the internets. Or maybe I am not searching properly so I decide to describe it as best I can here, maybe someone has encountered same issue and hopefully as a solution.
After 4 considerably successful first prints, that included a adapter for the vent, I moved printer to her new spot (inside has the balcony as a very cold temperature this time of year but had to do for the first ones),mount vent tube, then recalibrate (set home,then pressed z=0) give a quick test only to near to the end hear some sound and find plate is trying to go further up the axis then it can.
The issue seems to be plate does not set proper where the 0 is. The plate stays where I leave it after raising manually to be able to fit in the vat.
Possibly causes would,my guess related to temperature, but now inside I should nt have a problem if it even printed outside. Also in the last print, i had a incident with the red knob that you unscrew the remove the plate. The knob stayed in my hand and the screw in place and would not budge so I had to unscrew the 4 smaller screws to be able to remove tte plate.
Any help would be appreciated! I was having a lot of fun learning in the process and making my little miniatures and now I am very stuck with this. Thank you in advance!

翻譯年糕

What are the possible causes of resin not adhering to the print plate? I've had two partial failures in a row where the support skate has partly come away from the print bed during printing, deforming the printed part.
I'm using Elegoo grey and the base is curing for 60 seconds and the layers for 10.

翻譯年糕

has anyone here added-in any exterior CPU fan to the wiring on this machine? I've printed an exhaust hose adapter + in-line CPU booster fan set. Instead of having 2 separate plugs, I'd like to run the internal + external fan in parallel...I just don't know what would happen with the additional current draw on that circuit....

翻譯年糕

Hello again ? been here before and are now back better prepared. In short: last year I did buy a PhotonS and sold it again after a short time for several reasons: I was surpriced, it was SO messy, poisonous, stinking and the prints need post processing with IPA, UV, OMG, gloves and a lot of paper towels. All this just to produce small prints with awful mechanical properties ?

The biggest issue was however the fact that the printer should be used in a ventilated area so toxic fumes and smell not will do a health risk for my family or me.
Now my second PhotonS is ordered and I am prepared with a good ventilation solution found on (slow as h..) https://www.thingiverse.com/thing:3877012

It is no secret that I DO like the great details that the Photon can produce and I think it is a great hobby ?

翻譯年糕

Hi guys, do you spot the different colors white? I wonder did I put them too lóng or too shórt in the UV light? ....The ones at the bottom look a bit like they are “glow in the dark” and the ones on the right side at the top look “crème” ??? Should I UV- cure those longer? Or did I overdue?I used NXT Snow White from FunToDo....How long do you put small items them in the UV-light?
? ? THANX AGAIN ? ?

翻譯年糕

I have used up all my Anycubic Resin filters for the surplus resin. Any good alternatives while I await them in the mail? I have used up all my Anycubic Resin filters for the surplus resin. Any good alternatives while I await them in the mail? 翻譯年糕

Best place to get replacement build plates?

翻譯年糕

Hey guys, quick question.
I just had a print fail bc of a pre-supported file that didn't work for my setup. The print now sticks to the fep. What is the easiest way to remove the print without damaging or scratching my fep? Lift with my fingers? Use the plastic spatula? Soak it in ipa for a while?

翻譯年糕

The Swole Pikachu is next on the plate!! I started the print right after I took Illidan off the plate. Popped the plate back in and hit print!!

It is going to take almost 9 MORE FREAKIN HOURS!! Well, 8 hours and 40+ minutes from the time of this post!!!

It will be done somewhere around 12:30-1:15 am EST give or take!!

Can’t wait to wake up and see this be at least half finished lol

翻譯年糕