Anycubic Photon Printer Owners 造訪社團

原文網址 Craig Miln
2020-01-29 04:54:28

I’m looking at getting either an i3 Mega or an i3 Mega S. the S is like £45 more expensive (£130 vs £175).

Anyone know any reason to fork out the extra for the S? Just looking for advice really.

翻譯年糕

Matt Houghton
2020-01-29 04:59:22

Jacob Palmer
2020-01-29 07:41:44

Craig Miln
2020-01-29 08:06:53

Jacob Palmer
2020-01-29 08:22:09

Craig Miln
2020-01-29 08:23:25

Jacob Palmer
2020-01-29 08:24:07

Craig Miln
2020-01-29 08:24:21

Craig Miln
2020-01-29 08:33:47

原文網址 Tom Barnes
2020-01-29 04:36:00

Uuuh wut.
Print came out fine, but obviously can't have this.
I assume it's just a bed level issue, just got to find out where it's not right, I'm thinking that the beds tilted slightly back and to the left as I have had this happen a few times and it's been a bigger problem nearer the front and in the right of the build plate

翻譯年糕

James Cachia-Garrett
2020-01-29 04:42:26

Tom Barnes
2020-01-29 04:49:46

James Cachia-Garrett
2020-01-29 04:57:22

原文網址 JT Payne
2020-01-29 04:29:55

As I am printing, I know that the "ripping" sound is normal on the first layers, is it supposed to be like that for each layer though? I am trying to figure out if a print has failed, since I can't see the first inch or so because of the vat.

翻譯年糕

Neil Castle
2020-01-29 04:32:11

James Cachia-Garrett
2020-01-29 04:32:18

Will Koehler
2020-01-29 04:32:26

John Chrapkowski
2020-01-29 04:32:54

JT Payne
2020-01-29 04:34:46

Will Oliver
2020-01-29 04:36:15

JT Payne
2020-01-29 04:38:25

Will Oliver
2020-01-29 04:42:23

Smith Hayward
2020-01-29 04:51:28

Christopher Carfi
2020-01-29 05:21:08

Charles Lease
2020-01-29 05:37:33

JT Payne
2020-01-29 06:15:01

Zeb Christmas
2020-01-29 08:55:39

Richard Shapiro
2020-01-29 10:23:46

原文網址 Ken Chi Nok Ng
2020-01-29 04:23:37

interesting, while tried 7 times with these eyes, added supports in photon workshop then slice, 7 times with various settings on bottom and normal exposure, no luck

though I try adding supports in meshmixer and just slicer with standard setting, bingo... so whats the problem here ?

at least I got it to print now :)

翻譯年糕

Jacob Palmer
2020-01-29 05:10:36

Ken Chi Nok Ng
2020-01-29 05:13:02

Christopher Carfi
2020-01-29 05:24:21

Ken Chi Nok Ng
2020-01-29 06:20:53

Tyron Craft
2020-01-29 06:37:35

Ken Chi Nok Ng
2020-01-29 08:34:51

原文網址 Leonardo Aguilar
2020-01-29 04:16:36

Anyone know where can i get the orange piece?

翻譯年糕

Kevin Lems
2020-01-29 04:18:11

Matteo De Donatis
2020-01-29 04:35:09

Leonardo Aguilar
2020-01-29 04:39:32

原文網址 Joschka Röben
2020-01-29 04:15:48

Guys, I have designed these lock covers for my car. The little extension slips through a slot in the hub cap, to prevent the cover from getting lose. Currently I use Monocure grey, but I am not sure weather it will hold up and snap eventually. Would Elegoo ABS much better?

The extension needs to be flexible in order to slip through the above mentioned slot in the hub cap, but after that, an O-Ring will fix the cover and the extension has no mechanical load whats so ever.

翻譯年糕

Brian King
2020-01-29 04:40:20

Joschka Röben
2020-01-29 04:40:39

Brian King
2020-01-29 04:41:07

原文網址 Tamas Somogyi
2020-01-29 04:00:57

Hi guys. I am using anycubic clear resin. I read suggestion for using isopropyl alcohol for removing the half-cured resin straight after print. Do you know any other solvent? or a cheap soruce of isopropyl alcohol in EU?

翻譯年糕

Dudás Zsolt
2020-01-29 04:04:27