ATOM 3D Printer Group 造訪社團 » 線材相關話題

售ATOM 2.0 (已售出)
買來的主要用途是列印小玩具捐給基金會小朋友做娛樂及教學，因工作關係搬家，租屋處空間過小、隔音不好，不利於列印物件，故尋找有緣人。

1. ATOM 2.0 本機
2. ATOM 盔甲
3. Zebra Plate (免塗膠、免熱床可直接印，好拆件，黑白兩面都可印，白面未使用過 )
4. 原廠備品(如照片)
5. 超滑順的耗材轉盤
6. 特製的皮革 LOGO
7. 二硫化鉬修復性潤滑油 (還有半罐)
8. L扳手 + 神奇鏟刀
9. 線材:白色(未開封)，橘色、小麥色 (各剩7~8成左右，如圖)

功能一切正常，售出物如照片所示，自取不拆賣。
附上近期列印的作品：穿山甲一隻、恐龍一隻
已售出，謝謝大家

這是彈性軟料。
但是印出來左右兩邊的外觀與上下的外觀差很多！
為什麼會這樣呢？

So, good and bad things.
The good: I finally managed to have a successful dual color print.
It was a small print with blue and white PLA, hotend at 200 degrees, bed at 70, no glue and speed of 50 mm/s.
I then decided to print something larger, I only replaced the filament spools positions, so the blue will sit on E0 and the white on E1.
I used similar settings.
During the printing the wipe pillar begun to bend so I lowered the bed to 50 degrees.
The pillar detached from the bed at one point and I tried to save the print by glueing it back, with partial success, until the model also detached right when it reached the white layer, and at that point I stopped it since nothing more could be done to save it.
Some time before the failure both extruders had some weird noise.
I decided I'm done printing for today and unloaded both filaments so I can pack them.
At this point, and as the extruder picture show, I noticed the connector for the bowden pipe kind of displaced and on it's screwing part there's white stuff.
I did not tried to dismantle it for fear of more damage but right now I can't load filament to E1..
What could have caused it? Can the extruders heat up enough for the plastic to melt and ooze out of the connector?
How can I fix this?

翻譯年糕

Atom2.0列印，0.15mm層高，明燿鈦金

效果不錯…無上膠、清料塔開到75，混色改善不少…

Dual color printing with Cura:
I've looked at the manual given in the pinned post in this group and followed it.
Yet so far every dual color printing I tryed as failed.
My question is: at the advanced tab in Cura, should I change "Dual extrusion switch amount" to 120? I know Simplify need the filaments to be at position -120 mm for dual color prints.
And if it does need to be set to 120, should both filaments be at that position or just the second one?
Also does that work the same for when the second extruder has support materials like PVA?

翻譯年糕

Atom列印，明燿漂亮的藍色，藍色小精靈

【分享】

MK2 MK3
兩進一出共通版

1.
這個構造其實很簡單
看圖就應該知道99%
不過比較關鍵就是那個鎖喉管的螺絲
內外都有螺紋
所以可以把噴頭跟夾具(建議abs)牢牢的鎖再一起
這是我在公司的百寶箱無意間挖出來的(好巧...)
所以我真的不知道那叫啥名字(知道的喊一下...)

2.
這個的退換料長度大約45mm就可以
主要是可以減少拉絲長度
避免進料時堵塞
但這個是走歪門
因為牽絲問題不解決
進料時就會把部分拉絲一起帶進去
造成混料
所以
退換料的長度還是要看你用的料好壞來調教一下

3.
成功率嗎?
這個問題其實還蠻難回答的
跳過...哈哈

4.
圖檔
恩....這個要原廠批准我才敢PO
但其實這個自己畫也不難啦
(Fusion 360 讓我功力增加一甲子)

結論
沒有
因為我寫不出來...(哭)

.

颱風天就是要玩 阿童

不然要幹嘛

==================================

請問各位高手...

小弟遇到可惡的牽絲問題

回抽設 8 【 會 抽 太 少 嗎 ？】

Z 沒有提高 設 0 【 需要提高 + 回抽嗎？】

==================================

既然已經牽了可惡的絲

請問各位高手高高手

都如何使表面摸起來比較平坦一點就好

不用到發光發亮...

我用小刀慢慢切削......

削到手... 好酸~~~

PLA 好硬!!!

==================================

? ? ? ? ?

【請教S3D設定】
這個物件
下半部pla E0 temp 200
上半部abs E1 temp 240

我分別對COLOR 1 跟 COLOR 2 修改
但是溫度都一起動
不是200就是240

要怎麼設定
謝謝幫忙