ATOM 3D Printer Group 造訪社團

嗷嘸

# 總是再最後關頭出毛病的列印機

繼上一篇銷魂的印件之後。又來請教板上的高手...搞不懂這是怎麼回事，剛開始好好的，後來就走鐘了

補上圖片，左右兩邊都一樣

我好像很容易遇到印出來跟切片不一樣的東西，印件的大小是22cm x 4.1cm x 17.5cm（長寬高）

切片軟體 Cura 3.1
PLA 明燿的料
機型ATOM 3
速度 50/mms
填充25%
溫度185
熱床60
開木筏、無支撐

[求助］已爬文看過官網解決方案
目前印這兩個測試文件可以看到有斷料跟層高紋路紊亂。目前已嘗試解決方案有：
1: 更換喉管
2:重設平台平衡與自動調校
3:測試過溫度，溫度並沒有亂跳
4:換料

請教各位大神，單兵該如何處置？

各位大家好, 請問有人用Simplify 3D 4.1.2版本嗎?

原本是4.0.1及黃大哥的設定, 後來發生因素導致不得用4.1.2, 并嘗試在tool change script調整參數好幾次還是解決不了

問題:

在“噴頭跟熱床加熱完畢後開始打印前就產生退料120mm（應該是進料120mm完後在開始打印）的問題“，打印完成後可以順利退料120mm綫材再回歸原位。

所以有人可以給我指點方向嗎?因爲GOOGLE爬文的資訊卡在不同版本的代碼無法整理出邏輯點, 想不到頭緒,因此詢問， 謝謝大家抽空看文。

想請教一下如果Atom 2.5EX打印嘴塞了應該怎樣辦？

開工小印～邊印邊切片校正（左辺校正後右辺校正前）

Hello everybody,

I would to present to you the different steps of my ATOM 2.5EX printer evolution project:

- Step 1: disassembly of internal electronics + addition of TOP LED rails for lighting (Status => 100% finished)

- Step 2: replacement of the 8-bit motherboard with a 32-bit board (Duet2 Wifi) + addition of Side LED rails for lighting (Status => 100% finished)

- Step 3: development and integration of a 7' paneldue screen on the frame with laser-cutting aluminium parts + folding (Status => 75% finished)

- Step 4: manufacture of a rear plate to integrate the antenna of the Duet2 Wifi board + addition of an inter-switch for the internal lighting of the printer (Status => 75% finished)

- Step 5.1: replacement of the original nozzle with an 24v e-3D v6 standard version + a 24v Dragon Hotend version (Status => in progress 75% finished)

- Step 5.2: developpement and integration of a PCB for rapid disassembly of the print head, it's the same principle as ATOM 2.5 FX (Status => PCB are 100% developped and PCB manufacture is 50% finished)

- Step 5.3: replacement of the 12v power supply with a 24 volt version from Meanwell. (Status => to be mounted)

- Step 5.4: installation of a 24v to 12v converter to keep the original heating bed in 12v. (Status => to be mounted)

- Step 6.0: finishing integration of the 2 DYZE Filament sentinel to be able to stop the print when wire is out.

- Step 7.0 : integration of the ATOM laser module (if possible with the Duet2 Wifi). For this last step, I'm not sure if I can connect and run the laser on the Duet Board. I need to check first...

I will give you news about my project in few days / weeks...

✋

翻譯年糕

摩艾存錢筒，蜘蛛消光料，0.1mm 層高

ATOM 3 列印，列印時間約 30 小時

ATOM2.5雷雕初測

再來印了一下更大隻的，設定 280mm 高大小

0.1mm 層高，蜘蛛家黑色消光料，60mm 速度

全部耗時 50 小時 55 分鐘完成。

ATOM 3 長時間列印都給我蠻放心的，之前用創想系列長時間列印總是會怕失敗，ATOM 3 現在印兩三天都不太擔心。