• 3D列印服務
  • COSPLAY 3D 建模
  • #maker+t=market
  • 1
  • 2
  • 3

ATOM 3D Printer Group 造訪社團

原文網址 HS Fang
2018-09-05 21:19:28

哇！ 恭喜


原文網址 廖新弘
2018-09-05 18:32:12

變形方塊機器人，有興趣可以試試
尺寸內縮功能可能是必須的

Ya Hsuan Wu
2018-09-05 19:38:06

想到了小時候玩的ABC機器人~~(有沒有曝露年齡)


原文網址 黃瑞隆
2018-09-05 16:05:11

請問Simplify3D要如何設定ATOM 2.5EX雙色列印功能 請問Simplify3D要如何設定ATOM 2.5EX雙色列印功能

廖新弘
2018-09-05 16:33:23

先爬一下文，就知道了

Moko Jenson Huang
2018-09-05 17:09:04

Hawke ChienSheng Liu
2018-09-05 17:53:31

黃瑞隆
2018-09-05 18:50:46

Hawke兄可以請您指導一下嗎

Hawke ChienSheng Liu
2018-09-05 19:00:37

先容我問一下，怎麼lag了兩年才問這問題？

黃瑞隆
2018-09-05 19:10:58

最近才剛升級至2.5 EX 呵呵~

黃瑞隆
2018-09-05 21:50:49

謝謝廖大 有空趕快來試試看

Hawke ChienSheng Liu
2018-09-07 23:39:36

黃瑞隆
2018-09-10 16:19:08

感謝Hawke大分享

Hawke ChienSheng Liu
2018-09-10 17:34:41

要謝謝原創的黃大丙，不知道還在不在社團內⋯⋯


原文網址 朱俊錫
2018-09-05 14:55:52

按auto home後就出現這個狀況
感覺是極限開關沒感測到
請問各位，這是什麼地方出問題呢？

朱俊錫
2018-09-05 14:59:28

毛文謙
2018-09-05 15:02:55

影片有點不清楚 是滑臺沒有碰到機械限位嗎

廖新弘
2018-09-05 15:25:19

可能電線短路了，或者開關壞了，

邢鳳言
2018-09-05 21:55:57

按home之前, 先把滑台都往下拉10cm以上, 就好了

HS Fang
2018-09-16 13:28:00

限位開關的線鬆脫或是故障

王隆
2018-09-26 12:10:33

不好意思這是同一台印表機
檢查的過程中發現
當我們把所有主板上極限開關的線都拔除後 …… 查看更多

王隆
2018-09-26 12:20:00

極限開關換新的後問題還是一樣
最後把相關的東西都交換插一下
發現是照片上的孔位有問題 …… 查看更多

ChihJun Soong
2018-09-26 13:34:53

基本動作先用M119去檢查限位開關狀態是否正確?沒壓住顯示open,有壓住時顯示Triggerd

阿童
2018-09-27 09:03:23

小編建議您可以先用程式，確認看看微動是否正常運作？
https://atom3dp.squarespace.com/machine-issue-tw#head5
手邊有電錶的話，建議可以先量測晶片電壓看看， …… 查看更多


原文網址 Joe Abaquin Bing Aquino
2018-09-05 09:13:55

In Kisslicer, my parameter is 3 which means it will make the wall 3 around the wall, but how do you change the bottom and top layer to make it more than 3 ply or in layers?

In Slic3r, you can adjust the top and bottom layers to your likes separated as for the wall parameter.

翻譯年糕

Joe Abaquin Bing Aquino
2018-09-05 09:14:34

I just need to make the top and bottom thicker than the wall parameter.

黃俊傑
2018-09-05 10:05:24

ah.... here u r


原文網址 周佳佑
2018-09-04 18:16:21

作品分享...關節可動式地怪原型...配件陸續開發中..

高北熊
2018-09-04 19:13:58

太強大

Stanley Chen
2018-09-04 19:44:50

超帥！

邓家其
2018-09-04 20:23:11

thingiverse有打印文档吗


原文網址 謝昆良
2018-09-04 14:37:18

不好意思 請問一下

層和層之間的緊密度哪個參數決定的?

印完後成品容易裂開

黃俊傑
2018-09-04 14:39:15

感覺是喉管問題...

王祥豐
2018-09-04 14:39:39

溫度跟速度！

謝昆良
2018-09-04 14:40:28

跟重複填充 (Infill overlap)有關係嗎?

梁琄
2018-09-04 15:13:55

感覺是出料不順喔

陳順得
2018-09-04 15:54:45

什麼材料啊?

Scott Lai
2018-09-04 18:24:35

我的經驗是跟溫度、速度、線寬、填充密度有關


原文網址 Jörg Johow
2018-09-02 05:40:22

I do have a problem with the "auto level" function. The hotend wants to crash into the glass. Please see the video for more details.

翻譯年糕

葉世瑋
2018-09-02 10:07:33

So it did work before, right? Maybe there is something wrong in the main board. You can try to plug the autolevel switch connector to other socket (there should be 2 blanks at that column) and modify firmware.

Polo Huang
2018-09-02 20:23:32

As I known, there are new firmware alreay release,
what do not you download and take a try?

Hawke ChienSheng Liu
2018-09-03 01:55:31

I suggest you upgrade firmware to latest one ver.180529.
It will warn you before auto level starting if you don't adjust sensor well. You have to adjust the sensor to be just "clicked" by screw.
https://atom3dp.squarespace.com/firmware-en

Hawke ChienSheng Liu
2018-09-03 01:57:47

Jörg Johow
2018-09-05 02:20:36

Hi! I unplugged the sensor and measured it with a multimeter. It is „closed“ by default, meaning the circuit is closed and current can flow. When I push the nozzle upwards the switch goes „click“ and I can measure the circuit to be opened that way. This means, the switch is working. There might be a problem on the mainboard. Can I use a different connector on the board and route it it in the firmware? Thx!!

Jörg Johow
2018-09-05 02:23:41

One more thing: I‘m on the latest firmware and I do not get a warning. It seems like the firmware „thinks“ everything is good. ??‍♂️


原文網址 Jörg Johow
2018-09-02 04:33:42

Is there any higher firmware for the 2.0 (single extruder) than 2.0.7. ? When I upload ver.180529 or 1805329 - it seems to be the firmware for the 2.5 EX printer. On the website, it is said, that the new firmwares are working for the 2.0 printer. Please help! Thx!!

翻譯年糕

戴亙泰
2018-09-02 06:12:38

Hello，you can use the firmware ver. 180529，and choose version 2.0，menu position :Control -> Version，change this item and then Store Memory，and then can be use version 2.0~


 

發文排行榜

回文排行榜

熱門關鍵字