ATOM 3D Printer Group 造訪社團

原文網址 Nikki Gallagher Elliott
2018-01-02 06:45:13

I have been using my Atom 2.5EX for almost a year. Recently I started experiencing retraction problems. I have replaced the filament junction connector several times & each time it prints for 5 minutes before the black spacer falls out & causes the filament to grind. I relaced the nozzle about 4 months ago. I also replaced the PTFE tube in the nozzle, and have taken apart the dual extrusion junction connector countless times. Any ideas on how to fix the retraction?

翻譯年糕

Hawke ChienSheng Liu
2018-01-02 19:26:07

Replace it with this:
https://www.thingiverse.com/thing:2405124

Nikki Gallagher Elliott
2018-01-02 23:10:11

Thanks! I will try it.

原文網址 Lambo Ze En
2018-01-01 18:05:08

新年快樂
想請問大家哪裡買得到白色的軟料？
謝謝
(atom官網只有皮膚色的。) 新年快樂
想請問大家哪裡買得到白色的軟料？
謝謝
(atom官網只有皮膚色的。)

Efun Lai
2018-01-01 18:44:30

Modex好像有（這樣有違反版規嗎 ?

廖新弘
2018-01-01 20:06:15

各個拍賣網站找

許阿瑋
2018-01-02 16:04:45

PCHOME賣的EVA超好印

原文網址 陳奕廷
2018-01-01 09:31:02

各位前輩新年快樂

小弟想請問如何透過面板設定在列印中暫停然後更換完線材後再繼續列印呢印到一半發現線材快用完了阿~~~

小弟的設備是2.5EX

曾荐宏
2018-01-01 09:41:37

面版上有個pause print的指令，按完後再把料退出，重新進料並按繼續列印即可

Hawke ChienSheng Liu
2018-01-01 10:21:37

要選 Pause & Move 。

Jumi Chen
2018-01-01 10:39:04

想藉這個機會問一下...
記得之前有人提過有個小工具可以把不同料給融在一起...
請問這個工具要去哪買才有啊？？

陳奕廷
2018-01-01 16:35:31

結果我最後因為不想浪費料就直接首在機器旁邊等料用完的時候馬上再插入新料竟然成功了 ?

原文網址 Birk Binnard
2018-01-01 07:17:09

Uh oh!

Print became unstuck from printbed while I was out running. Looks like a thermistor wire got broken because printer stopped with MINTEMP error. Since I can't heat up the hotend normally I may try torching it. Or, if I can find a spare hotend in my parts box I may just cut the wires and replace the whole thing, I've become pretty adept at splicing the heater & thermistor wires by now.

翻譯年糕

Birk Binnard
2018-01-01 14:18:13

It turned out that replacing the entire hotend was the easiest solution. Fortunately I had a spare in my parts box that had all the necessary components except the connector on the ends of the heater disk wires.

But after careful inspection of the con nector from the above hotend I saw how to remove the wires from the connector and reconnect it to the wires from the replacement hotend. I should be good to go in the morning after I finish stuffing the wires & PTFE into the long plastic sheath.

黃大丙
2018-01-07 00:18:05