ATOM 3D Printer Group 造訪社團

原文網址 Bless Ma
2017-08-05 12:43:53

我剛剛才發現原來kisslicer一直都有在更新
只是官網的位置換了

Dan Salvador
2017-08-05 13:58:16

Do you recommend it ? , how's the result to compare with simplify3d?

Ark Chuang
2017-08-05 18:46:03

推薦用1.6嗎？

Moko Jenson Huang
2017-08-06 11:21:27

請教一下，那個設定視窗怎麼跟主畫面合併呢？

蘇子中
2017-08-06 14:21:35

新版本已可支援atom雙色了嗎？

Tk Leung
2017-08-06 21:17:24

剛download 了, 但執行的時候被防毒block 了, file也被移除。

原文網址 Bless Ma
2017-08-05 12:29:07

大約一個多星期前就拿到了
但因為我有改進料方式所以多花了點時間安裝

目前有遇到的問題就是
保養時要鎖滑軌上的球頭變的很難鎖

陳方瑜
2017-08-05 12:38:30

原本我們有打算把後面兩片也改成磁吸式，保養的時候比較好拆另外兩片罩子，但後來發現印太大面積的東西時，電線的管子如果甩到罩子，有可能罩子會掉下來，才維持原樣，或者是要去找更強的磁鐵（不過都是成本啊...)

李安茂
2017-08-05 13:13:28

這線好大卷啊

原文網址 Yu-Hsuan Hung
2017-08-05 12:18:29

詢問大大Neutron的marlin修改問題
繼上次以為是auto level壞掉產生的問題，實際上是因為小弟吧噴頭換成e3d，結果噴頭太長所以才會戳到最底，這個部分想知道marlin要如何修改autolevel下降的高度呢? 詢問大大Neutron的marlin修改問題
繼上次以為是auto level壞掉產生的問題，實際上是因為小弟吧噴頭換成e3d，結果噴頭太長所以才會戳到最底，這個部分想知道marlin要如何修改autolevel下降的高度呢?

廖新弘
2017-08-05 13:28:39

改第347行 # define MANUAL_Z_HOME_POS 225//195 // For delta: Distance between nozzle and print surface after homing.中的225數值

Keisuke Lin
2017-08-08 20:04:19

Autohome之後用1mm把Z軸慢慢降下來，快碰到玻璃時換成0.1mm的，慢慢降到碰到玻璃，然後看面板Z高度剩下多少，從marline裡面扣掉

童化金
2017-09-08 00:43:23

借問你有遇到level bed後，再使用auto home會撞噴頭的問題嗎?
但重開機不先使用level bed後，直接使用auto home沒問題

原文網址 楊為巽
2017-08-05 11:31:26

firmware update的問題…錯誤訊息在struct fpos_t？

ChihJun Soong
2017-08-05 12:03:20

這是IDE 新舊版問題 , 換成舊版arduino ide , 或是將fpos_t 改成fpost

Dennis Chen
2017-08-05 12:22:31

因為新的Arduino 也定義了 fpos_t，Marlin也有定義自己的 fpos_t造成重覆定義，直接 search & replace all "fpos_t" 改成其他名稱就行了，基本上也只要改兩個檔案就行了: SdBaseFile.cpp, SdBaseFile.h
$ grep -n fpos_t *.{cpp,h}
SdBaseFile.cpp:297:void SdBaseFile::getpos(__fpos_t* pos) {
SdBaseFile.cpp:928: __fpos_t pos;
SdBaseFile.cpp:1495:void SdBaseFile::setpos(__fpos_t* pos) {
SdBaseFile.h:34: * \struct __fpos_t
SdBaseFile.h:38:struct __fpos_t {
SdBaseFile.h:43: __fpos_t() : position(0), cluster(0) {}
SdBaseFile.h:208: void getpos(__fpos_t* pos);
SdBaseFile.h:212: void setpos(__fpos_t* pos);

楊為巽
2017-08-05 22:44:18

這：太難了…

Dennis Chen
2017-08-06 16:15:32

https://www.facebook.com/groups/atom3dp/1959857627585856/

原文網址 戴光宏
2017-08-05 05:01:24

拆噴頭半節鐵氟龍管斷在裡面
折騰了幾小時發現原來只要拿打火機烤一下拿東西硬刺進去就可以挖出來了

廖新弘
2017-08-05 06:57:16

原文網址 傑森包恩
2017-08-05 02:46:04

大家好，小弟最近工作忙，有些東西組不完，所以大算要出清，品項如下：
1. Neutron 套件，先前跟團組的，如照片所示含列印件, 螺桿,光軸等機械部份，不含馬達等其他電子零件，售500元
2. MKS Gen 1.4 主板 + MKS Mini12864 LCD + 未拆 4988 x4 ，售800元
3. MKS Base v1.4 + 1602 LCD，是升級拆下，售500元
4. Mega2560 + RAMPS 1.4 + 1602 LCD，售500元
5. LV8279 128細分步進馬達驅動IC x4，售500元

チェン幸せな
2017-08-05 05:06:48

收1

黃山姆
2017-08-05 06:25:25

收2

ChihJun Soong
2017-08-05 06:48:27

收5

YiGong YiTu
2017-08-05 07:36:34

收4

翟玉申
2017-08-05 07:42:54

排1

林界亨
2017-08-05 07:48:45

排1

Yu-Zhi Kang
2017-08-05 08:11:45

收1

Yong Siang Lin
2017-08-05 09:23:01

排1

傑森包恩
2017-08-06 13:23:34

感謝各位，目前1, 4, 5 已售出

傑森包恩
2017-08-08 15:34:31

2也售出了，只剩下3

Arthur Shaw
2017-08-10 22:27:14

上班要專心

原文網址 Roy Lo
2017-08-05 00:36:40

橘子腦師畫的～

橘子腦師
2017-08-05 09:22:32

Ro 大技術高超，印的好棒啊

原文網址 Fabio Hasseck
2017-08-04 22:57:11

Dual color printing with Cura:
I've looked at the manual given in the pinned post in this group and followed it.
Yet so far every dual color printing I tryed as failed.
My question is: at the advanced tab in Cura, should I change "Dual extrusion switch amount" to 120? I know Simplify need the filaments to be at position -120 mm for dual color prints.
And if it does need to be set to 120, should both filaments be at that position or just the second one?
Also does that work the same for when the second extruder has support materials like PVA?

翻譯年糕

黃俊傑
2017-08-07 09:24:43

1. just download the official cura setting profile.
2. put the filament as photo.
3. u can check the support setting. it depends which side u loading the pva.

Fabio Hasseck
2017-08-07 11:50:33

Should both filaments be loaded all the way?
I tried that once but the printer did not switch well between E0 and E1 as E0 filament was still too close to the hotend.
Do i need to change the Dual extrusion switch amount to 120 when slicing?

原文網址 Harry Cayne
2017-08-04 17:25:29

What do you think about
https://www.youtube.com/watch?v=rvPdoUrlAV4 ?

翻譯年糕

原文網址 Harry Cayne
2017-08-03 15:30:59

Check my Super Light Printhead, heated chamber compatible under 100g with extruder

翻譯年糕

Vincent Liu
2017-08-03 15:59:59

Water cooling system??

Harry Cayne
2017-08-03 16:05:42

Yes, water jacket on cold side!

Birk Binnard
2017-08-04 00:31:56

Is this avaiablefor purchase? How difficult would it be to adapt it to the Atom2 carrier? Is there anything connected to the hotend beyond:
1. Wires for heater & thermistor
2. Wires for extruder motor
3. Bowden tube
4. Water input & output tubes

Harry Cayne
2017-08-04 16:00:02

Yes, the final version will be for sale ! Carriage needs a fish-eye adapter and different parallel rods, couple lines changed in Marlin the rest is coming with the print head, the water chiller mount will be self printable !

Harry Cayne
2017-08-04 17:24:19

final version will have out of chamber cooling, too : https://www.youtube.com/watch?v=rvPdoUrlAV4