Anycubic Photon Printer Owners 造訪社團 » resin

原文網址 Philip Nicholls
2020-03-07 17:48:43

Straight in at the deep end and I managed my first print of a fan balancer. Really impressed by the quality. Only issue is a layer shift when I paused to add resin.

翻譯年糕

Mike Fleming
2020-03-07 18:15:59

Dan Andersson
2020-03-07 21:36:58

Mike Fleming
2020-03-07 21:49:03

David Kane
2020-03-07 22:13:53

Dan Andersson
2020-03-07 22:32:17

原文網址 Paul Boyle
2020-03-07 16:43:56

Any advise on the clearest clear resin, non yellow, will formlabs clear work with photon s.

Thank you

翻譯年糕

Jaco Norchie Nortje
2020-03-07 17:03:26

原文網址 Jamie Masotti
2020-03-07 14:54:38

Considering getting another resin printer to keep up with the insane amount of commissions I've been behind on because I only have one printer at the moment (photon S). Which would you reccomend between the Photon, zero, Phrozen or Mars? :)

考慮得到另一台樹脂印表機跟上我一直落後的瘋狂的傭金, 因為我目前只有一台印表機(photon s). 你會在光子, 零, phrozen還是火星之間重新組合哪一個? :)

· 查看原文 · 為此翻譯評分

Sean O'Hayer
2020-03-07 14:59:45

Jesper Hvid
2020-03-07 15:01:02

Rantinan Winters
2020-03-07 15:04:39

Dane Bennett
2020-03-07 15:05:41

Rantinan Winters
2020-03-07 15:05:50

Ernest Dam
2020-03-07 15:11:13

Jonny Marable
2020-03-07 15:11:41

Jamie Masotti
2020-03-07 15:13:28

Jamie Masotti
2020-03-07 15:13:48

Adil Muschelewicz
2020-03-07 15:21:11

Steve Marshall
2020-03-07 15:35:20

Tomislav Štampar
2020-03-07 15:44:22

Jonny Marable
2020-03-07 15:52:00

El Ner Endem
2020-03-07 15:57:30

Ben Messer
2020-03-07 16:23:29

Ben Messer
2020-03-07 16:24:21

John Chrapkowski
2020-03-07 16:33:15

John Chrapkowski
2020-03-07 16:33:37

John Chrapkowski
2020-03-07 16:34:16

Marko Sallinen
2020-03-07 16:48:36

Patric Broborn
2020-03-07 17:21:30

Dan Andersson
2020-03-07 17:36:43

Mimmo Lagonigro
2020-03-07 17:50:12

Dave Dewees
2020-03-07 18:07:05

Francis X Benz
2020-03-07 20:09:57

Constantine Greanias
2020-03-07 20:44:10

Nate Mueller
2020-03-07 20:46:35

Jason Willis
2020-03-07 20:53:12

Lucian Lilu
2020-03-07 22:20:24

Ken Chi Nok Ng
2020-03-07 22:46:26

Jamie Masotti
2020-03-08 00:43:12

Lucian Lilu
2020-03-08 00:45:23

Jamie Masotti
2020-03-08 01:26:47

Jamie Masotti
2020-03-08 01:27:14

Rantinan Winters
2020-03-08 02:25:58

John Matthew
2020-03-08 04:39:32

Steven Tooze
2020-03-08 04:41:37

John Matthew
2020-03-08 04:49:00

Grant Weaver
2020-03-08 10:09:38

原文網址 Dan Buga
2020-03-07 14:32:51

Hello guys I bought my first photon (not s) . Seller give me resin anycubic basic orange (( What setting you recomand for this resin for 0.05 layer ? Inclusive I need z lift distance , z lift speed and , z retract speed )

翻譯年糕

Franz Meriles
2020-03-07 14:35:34

Willie Randell
2020-03-07 14:49:38

Yessik Ziiq
2020-03-08 10:09:49

原文網址 Cameron Lee Johnson
2020-03-07 14:31:06

So i had my first failure. I was printing a large piece of a display model (a little smaller than a baseball) and then super tiny versions of that model as well.

They all broke off the supports. Since this was my first time using opaque resin, im assuming its under exposure? Or would the supports have failed as well? What interesting is i had 2 sets of the smaller model pieces. You can see the base layers of one on the plate there. But the other has nothing

Anycubic black
4 base layers at 75 seconds.
.05 layer height at 8 seconds

翻譯年糕

Scott Pavlich
2020-03-07 15:09:32

Jesper Hvid
2020-03-07 15:47:22

原文網址 Jacob William Curtis
2020-03-07 14:00:59

Hey Folks,

I'm having some prints come out slightly deformed. do I need more supports for the lowest points? I tried increasing exposure time with this resin to slightly above the recommendations, and the room I'm printing in is about 70F.

翻譯年糕

Scott Pavlich
2020-03-07 15:50:35

原文網址 Brett Hogan
2020-03-07 13:36:21

I have seen the PDF for the settings for using Anycubic resin but that's at .05 layer height. But i want to do .02 or .01 layer height. Would I use the same settings?

翻譯年糕

John Chrapkowski
2020-03-07 13:38:38

John Chrapkowski
2020-03-07 13:39:10

Bob Deblier
2020-03-07 13:41:35

Scott Pavlich
2020-03-07 15:41:10

Scott Pavlich
2020-03-07 15:41:25

Scott Pavlich
2020-03-07 15:42:16

Scott Pavlich
2020-03-07 15:42:45

Scott Pavlich
2020-03-07 15:43:57

原文網址 Mika Gruszka
2020-03-07 11:32:29

Loving these flexi trilobite critters! They are so fun and take barely any resin!

Also: anybody got any suggestions for a dice tower that isn't too big for the photon? All the ones I'm finding are too big and I don't want to resize them.

https://www.thingiverse.com/thing:3839472

翻譯年糕