Anycubic Photon Printer Owners 造訪社團 » EX

原文網址 Adam Michael Hennebeck
2020-03-04 11:17:11

All of these were printed using PrusaSlicer Orientation. The part of the base that was pointed down is flattened on each of these printed at different times. Thoughts?

LH-.05mm
Bottom Layer Count-8
Exposure Time: 10
Bottom Exposure Time: 90
Light Off Delay-1
Bottom Light Off Delay-3

AC Green. 20C

翻譯年糕

Adam Michael Hennebeck
2020-03-05 11:22:03

Adam Michael Hennebeck
2020-03-06 13:24:49

原文網址 Michael Kiaunis
2020-03-04 09:54:28

Piece of seemingly good model extending very far down in when slicing?

I have attached a photo of the model in Photon Workshop (Chitubox is showing the same results), as well as pictures of the finished model and the first layer in Validator. Does anyoen know why these seemingly ghost layers are appearing when trying to slice? I will link to the file in the comments. I have never seen this happen before.

Thanks to anyone who takes a crack at figuring this out...

翻譯年糕

Michael Kiaunis
2020-03-04 09:54:36

Stephen Hill
2020-03-04 21:40:42

Michael Kiaunis
2020-03-04 23:46:58

原文網址 Jeremiah Chetwood
2020-03-04 08:49:30

Well I gave up on that b9 creations emerald green that I was given to try, I can print exposure test then after that not good....

翻譯年糕

原文網址 Erik Morris
2020-03-04 08:19:45

Mixing Resins for Noobs Please...

I started using AC green.. way too brittle. I switched to Siraya ABS-Like Fast Gray, and have been very happy (with a few exceptions). I've experienced some smaller parts break off when dropped (I know you can't avoid all injuries). However, when a player in my campaign buys a model from Hero Forge and I print it off for them, I'd like it to not break the very first time he puts it on the table.

So, what is the resin recommendations to mix with my Siraya Fast? I've heard Tenacious at 10%?

Questions:

1- How do you go about mixing? In a separate bottle? In the VAT? etc.

2- How precise do folks need to be, when mixing %'s? I mean, do folks just eye ball it?

3- Is there a better resin out there for mixing than the Tenacious? One that doesn't cost an arm/leg? I mean, the Tenacious is double the cost of the Fast Gray...

Thanks

翻譯年糕

Greg Chapman
2020-03-04 08:22:55

David Burgan
2020-03-04 08:28:51

Nathaniel Red Weidner
2020-03-04 08:33:25

Scott Ball
2020-03-04 08:42:29

Scott Pavlich
2020-03-04 08:43:09

Scott Pavlich
2020-03-04 08:47:15

Scott Ball
2020-03-04 08:48:50

Scott Pavlich
2020-03-04 09:03:11

Scott Ball
2020-03-04 09:20:02

Erik Morris
2020-03-04 09:32:30

Len LaGuardia
2020-03-04 09:44:56

Nathaniel Red Weidner
2020-03-04 09:50:09

Len LaGuardia
2020-03-04 10:21:47

Nathaniel Red Weidner
2020-03-04 10:32:36

Nathaniel Red Weidner
2020-03-04 10:34:28

Len LaGuardia
2020-03-04 10:34:29

Nathaniel Red Weidner
2020-03-04 10:35:18

Len LaGuardia
2020-03-04 10:35:41

Len LaGuardia
2020-03-04 10:37:06

Nathaniel Red Weidner
2020-03-04 10:38:17

Len LaGuardia
2020-03-04 10:39:36

Keegan Bradford
2020-03-04 12:16:35

Nathaniel Red Weidner
2020-03-04 12:18:00

Keegan Bradford
2020-03-04 12:18:29

Nathaniel Red Weidner
2020-03-04 12:19:15

Keegan Bradford
2020-03-04 12:20:00

Erik Morris
2020-03-06 00:21:23

Scott Pavlich
2020-03-06 01:46:14

Erik Morris
2020-03-06 02:12:54

Scott Pavlich
2020-03-06 02:21:45

原文網址 Scott Kernaghan
2020-03-04 06:50:15

I learned something today the hard way. I’ve had my ACP for a week, my first DLP, but I’m not new to 3D printing having used FDM machines for years. After a week of looking at blobs dirtying up my FEP and reading a billion and 1 posts about how to stop stuff sticking to it, I did something drastic: I ignored the same blunt and respected answers and thought about problem myself.

The issue was that I am using a bottle of Resin that turns up in none of the spreadsheets - Anycubic Eco Black. I got the eco by accident, but I wanted black because I’m going to use this machine as part of a specific workflow. There’s some eco products on the spreadsheet so I used some of the data as a basis. As the prints failed and I found myself cleaning and readjusting, I kept on sticking to the same logic: try greater exposure times on your base. I must have the alignment wrong.

And still I spent half my afternoon cleaning stuff... with square blobs my only friend. There were pops and pops.. something seemed to be sticking.. but no. All to the FEP.

Eventually it occurred to me: is it possible that I’m over-exposing this to the point of fusing it to the FEP? And online search came up with only a couple of hints that this could happen. But I tried it anyway - dropping it below the initial 60 seconds I first tried. And blow me down if it didn’t work perfectly. I used a calibration piece (as shown) and it simply pulled up perfect.

So to any newbie getting stuck prints and getting the same 4 answers when you ask for help, my lesson is this: ignore those dogmatically repeated questions. They aren't diagnosing, and you shouldn't outsource it.

Oh... and yes, you can over expose your base. Try dropping the time.

翻譯年糕

Jarrod Smith
2020-03-04 06:56:32

Nipuna Gunarathne
2020-03-04 07:02:20

Robert Nisson
2020-03-04 09:32:16

Cannon Rigger
2020-03-04 12:00:32

Scott Kernaghan
2020-03-04 12:01:21

Niall Forrester
2020-03-04 18:05:46

Scott Kernaghan
2020-03-04 18:19:08

Niall Forrester
2020-03-04 18:20:57

Fabian Ruyters
2020-03-04 21:12:55

原文網址 Saïmone Goblet
2020-03-04 05:37:41

I have 2 issues with my late prints, i don't know exactly why. Maybe some here could help !

- First, 2 prints in a row, my raft that was almost occupying all the space on the build plate got detached a bit and warped for some milimetters. Causing part of my supports to not print properly.

- Second, but I think it's is linked to 1 : in some areas, my raft is 1mm tall and in some other, it's 3mm. So i'm wasting way too much resin for the raft.

I already releveled the bed, but I don't see any reason why it would warp and print more than it should.

Maybe my FEP is damaged or simply too old ?

翻譯年糕

原文網址 Florian Reil
2020-03-04 04:29:58

Hey folks,
we printed these objects on a an anycubic photon at 100 microns with DruckWege Type D Flex and wanted to share the results as we are really happy with the output of the prints. https://shop.druckwege.de/en/resin/55-139-druckwege-resin-type-d-flex.html#/36-size-05_kg Models used: https://www.myminifactory.com/object/3d-print-bmx-grip-ninjaflex-12909 https://www.myminifactory.com/object/3d-print-transmission-belt-1021 https://www.thingiverse.com/thing:526969

嘿, 朋友們,
我們將這些物件列印在一個100微米的光子上, 帶有druckwege d型flex, 並希望分享結果, 因為我們對列印的輸出非常滿意.
https://shop.druckwege.de/en/resin/55-139-druckwege-resin-type-d-flex.html#/36-size-05_kg
使用的模型:
https://www.myminifactory.com/object/3d-print-bmx-grip-ninjaflex-12909
https://www.myminifactory.com/object/3d-print-transmission-belt-1021
https://www.thingiverse.com/thing:526969

· 查看原文 · 為此翻譯評分

Dan Elent
2020-03-04 04:52:05

Florian Reil
2020-03-04 04:53:36

Dan Elent
2020-03-04 04:54:22

Dan Elent
2020-03-04 04:55:03

Florian Reil
2020-03-04 04:55:16

Dan Elent
2020-03-04 04:56:00

Florian Reil
2020-03-04 04:57:48

Dan Elent
2020-03-04 04:59:30

Florian Reil
2020-03-04 04:59:33

Florian Reil
2020-03-04 05:00:56

Saša Sinek
2020-03-04 05:00:58

Dan Elent
2020-03-04 05:01:30

Florian Reil
2020-03-04 05:11:00

Paul Dodd
2020-03-04 05:15:33

Arnar Helgi Adalsteinsson
2020-03-04 06:28:04

Florian Reil
2020-03-04 06:50:26

Mike Chess
2020-03-04 06:57:53

Komet Tou Lee
2020-03-04 07:19:33

Chris Vasquez
2020-03-04 07:31:17

Giancarlo Arriola
2020-03-04 07:40:02

RC Vaporthreedprint
2020-03-04 08:50:37

Patrick Sean Stock
2020-03-04 09:14:11

Marie Stevens
2020-03-04 10:01:31

Dustin Wiebe
2020-03-04 11:41:32

Dan Elent
2020-03-04 13:00:09

Florian Reil
2020-03-04 13:37:36

Florian Reil
2020-03-04 13:42:17

RC Vaporthreedprint
2020-03-04 14:11:57

Tom Sargison
2020-03-04 15:44:24

Damian Jerewski
2020-03-04 16:30:59

Holden8702
2020-03-04 20:23:10

Thomas Weissböck
2020-03-05 04:30:01

Jairo Ledesma
2020-03-05 06:34:03

Dan Elent
2020-03-05 07:05:52

Andrea Bellusci
2020-03-05 07:12:12

Daphinie Clark
2020-03-06 00:25:42

Luis Bivar Ramos
2020-03-07 02:49:12

Antonio Regidor
2020-03-07 04:05:12

Micah Vestal
2020-03-11 13:39:40

Florian Reil
2020-03-11 16:26:51

Florian Reil
2020-03-11 16:27:34

Florian Reil
2020-03-11 21:24:04

Dan Elent
2020-03-11 21:32:46

Florian Reil
2020-03-11 21:35:22

Dan Elent
2020-03-11 21:39:36

Florian Reil
2020-03-11 21:48:12

Dan Elent
2020-03-11 21:55:28

Florian Reil
2020-03-11 22:02:25

Florian Reil
2020-03-11 22:02:42

Dan Elent
2020-03-11 22:06:25

Jen McVey
2020-03-11 22:13:37

Florian Reil
2020-03-11 22:19:30

Florian Reil
2020-03-11 22:20:40

Florian Reil
2020-03-11 22:21:23

Jen McVey
2020-03-11 22:24:19

Florian Reil
2020-03-11 22:28:56

Jen McVey
2020-03-11 22:31:15

Florian Reil
2020-03-11 22:40:46

Jen McVey
2020-03-11 22:45:34

Dan Elent
2020-03-11 23:00:29

Florian Reil
2020-03-11 23:04:17

Dan Elent
2020-03-11 23:10:33

Micah Vestal
2020-03-13 00:49:11

原文網址 Paul Metcalfe
2020-03-04 03:39:53

A breeding pair. The one on the right is our works printer, my own is on the left. Had an interesting issue crop up with the works one, took a good print of it on Friday and set another away. Came back to it Monday morning to find nothing, no print, nothing stuck to the fep sheet. Thinking I’d cocked up the supports I bolstered them up, checked the level, filtered the resin and started again. Same result. This afternoon I tried an exposure test on it to find the whole lcd would illuminate at what appears to be half power, irrespective of which exposure mode was selected, re-updated the firmware (to the same version as it had received a fortnight ago), repeated the exposure and all was as it should be, ran my xyz test piece and it printed fine, so it’s back underway again now hoping that the issues are done with. I am puzzled as to what was the route cause, but at least I have some form of solution. Cheers

翻譯年糕

Nipuna Gunarathne
2020-03-04 04:58:33

Paul Metcalfe
2020-03-04 05:17:25

Luiz Junior
2020-03-05 08:07:18

Paul Metcalfe
2020-03-05 17:11:10

原文網址 James Forder
2020-03-04 03:25:54

I've just been reading the posts about the excessive nudity in this group, currently, I'm fully dressed, but each to their own ;) I can't say I've seen anything I would consider offensive but others obviously have. I think there should be a vote before the admins ban pictures of little resin models that show the natural female form.

翻譯年糕

Ben Wood
2020-03-04 03:33:38

Ian Gill
2020-03-04 03:34:35

Ian Gill
2020-03-04 03:37:06

John Aldred
2020-03-04 03:38:15

John Aldred
2020-03-04 03:38:44

Dominick Trascritti
2020-03-04 03:40:21

Connor Goodwolf
2020-03-04 03:42:05

Ben Wood
2020-03-04 03:42:54

Jacob Palmer
2020-03-04 03:43:01

Jim Monaco
2020-03-04 03:44:05

Connor Goodwolf
2020-03-04 03:44:15

Joel Mendoza
2020-03-04 03:45:08

Allison Janssens
2020-03-04 03:49:09

Oksana Shevchenko
2020-03-04 03:50:17

Oksana Shevchenko
2020-03-04 03:50:26

Joel Mendoza
2020-03-04 03:50:28

Benjamin Cole
2020-03-04 04:02:50

Bob Deblier
2020-03-04 04:05:42

Joel Mendoza
2020-03-04 04:06:40

Ray Sears
2020-03-04 04:08:10

David Arnold
2020-03-04 04:08:26

Tyler Tolley
2020-03-04 04:09:05

Zena Andreou
2020-03-04 04:09:23

Mark Stevenson
2020-03-04 04:13:19

Shikaria Serenyty
2020-03-04 04:13:52

Kaile Riser
2020-03-04 04:14:03

Richard Shapiro
2020-03-04 04:14:36

Thomas Harrell
2020-03-04 04:15:18

Jesse Ireland
2020-03-04 04:16:40

Joel Mendoza
2020-03-04 04:17:32

Jesse McMahon
2020-03-04 04:17:44

Thomas Harrell
2020-03-04 04:18:25

Smith Hayward
2020-03-04 04:19:37

Tom Ligman
2020-03-04 04:19:40

Shikaria Serenyty
2020-03-04 04:20:17

Smith Hayward
2020-03-04 04:20:33

Michael Gonzalez
2020-03-04 04:20:45

Tom Ligman
2020-03-04 04:21:17

Bert Harvey
2020-03-04 04:22:59

Zeb Christmas
2020-03-04 04:25:38

Eric Dixon
2020-03-04 04:28:32

Zakkari Clark
2020-03-04 04:29:10

Evan Boone
2020-03-04 04:35:05

Mark Stevenson
2020-03-04 04:36:38

Gregore Conn
2020-03-04 04:41:34

Joshua Mahan
2020-03-04 04:41:43

Guido Fawkes
2020-03-04 04:43:42

Melecio Guzman
2020-03-04 04:44:30

Allison Janssens
2020-03-04 04:45:41

Joshua Mahan
2020-03-04 04:45:42

Paul Holmes
2020-03-04 04:46:24

Joshua Mahan
2020-03-04 04:50:08

Zakkari Clark
2020-03-04 04:52:14

Alwin Chan
2020-03-04 04:53:57

Joseph Dolan
2020-03-04 04:58:24

Liam Kaiser Wilhelm Smith
2020-03-04 05:03:29

Theo Brinkman
2020-03-04 05:06:04

Mark Owens
2020-03-04 05:11:06

Paul Dodd
2020-03-04 05:12:39

Lex Cole
2020-03-04 05:19:01

Tristan Jones
2020-03-04 05:27:38

Benjamin Oppenheimer
2020-03-04 05:42:02

Steve Hornabrook
2020-03-04 05:42:39

Eis Habenicht
2020-03-04 05:48:05

Michael Winchell
2020-03-04 05:48:51

Tim Parks
2020-03-04 05:50:08

David Collinson
2020-03-04 05:58:02

Ryan Neal
2020-03-04 05:58:33

Chris Willhelm
2020-03-04 06:06:24

Guido Fawkes
2020-03-04 06:08:15

Charlie Yoshi Locke
2020-03-04 06:14:27

Cynthia Reed Nottingham
2020-03-04 06:19:05

Cynthia Reed Nottingham
2020-03-04 06:21:12

Alec Traynor
2020-03-04 06:23:59

Benjamin Tolputt
2020-03-04 06:24:28

Paul Carter
2020-03-04 06:25:29

Stephen Farrell
2020-03-04 06:26:58

Andy Tanguay
2020-03-04 06:33:29

Tim Parks
2020-03-04 06:35:29

Benjamin Tolputt
2020-03-04 06:40:27

Benjamin Tolputt
2020-03-04 06:42:15

Tim Parks
2020-03-04 06:44:00

Gary Noble
2020-03-04 06:52:18

Sunny Shukla
2020-03-04 06:56:56

Connor Goodwolf
2020-03-04 07:00:32

Josh Dalgliesh
2020-03-04 07:01:25

Brian Wright
2020-03-04 07:03:19

Cheung Kinmen
2020-03-04 07:05:44

Josh Dalgliesh
2020-03-04 07:07:09

Alastair Graham
2020-03-04 07:08:30

Josh Dalgliesh
2020-03-04 07:09:12

Josh Dalgliesh
2020-03-04 07:10:05

Paul Carter
2020-03-04 07:13:16

Jarrod Smith
2020-03-04 07:14:09

Kevin Rank
2020-03-04 07:23:53

Benjamin Tolputt
2020-03-04 07:24:05

Benjamin Tolputt
2020-03-04 07:29:08

Adam Rodgers
2020-03-04 07:33:44

Benjamin Tolputt
2020-03-04 07:39:35

Yessik Ziiq
2020-03-04 07:39:39

Craig Cooper
2020-03-04 07:42:19

Benjamin Tolputt
2020-03-04 07:43:26

Adam Rodgers
2020-03-04 07:43:27

Yessik Ziiq
2020-03-04 07:44:50

Adam Rodgers
2020-03-04 07:45:52

Yessik Ziiq
2020-03-04 07:47:55

Adam Rodgers
2020-03-04 07:49:01

Ky Lane
2020-03-04 07:49:15

Sean Smith
2020-03-04 07:52:20

Sean Smith
2020-03-04 07:55:04

Zakkari Clark
2020-03-04 07:55:11

Brian Wright
2020-03-04 07:55:24

Benjamin Tolputt
2020-03-04 07:56:38

Sean Smith
2020-03-04 07:57:09

Zakkari Clark
2020-03-04 08:00:30

Yessik Ziiq
2020-03-04 08:00:31

Benjamin Tolputt
2020-03-04 08:01:30

Zakkari Clark
2020-03-04 08:03:54

Sean Smith
2020-03-04 08:05:23

Benjamin Tolputt
2020-03-04 08:05:29

Benjamin Tolputt
2020-03-04 08:05:54

Zakkari Clark
2020-03-04 08:06:45

Benjamin Tolputt
2020-03-04 08:07:17

Sean Smith
2020-03-04 08:07:50

Zakkari Clark
2020-03-04 08:08:47

Sean Smith
2020-03-04 08:13:40

Benjamin Tolputt
2020-03-04 08:14:35

Sean Smith
2020-03-04 08:15:05

Benjamin Tolputt
2020-03-04 08:19:16

Sean Smith
2020-03-04 08:27:01

Sean Smith
2020-03-04 08:27:30

Sean Smith
2020-03-04 08:28:50

Benjamin Tolputt
2020-03-04 08:31:46

Benjamin Tolputt
2020-03-04 08:32:50

Ian Gill
2020-03-04 08:36:49

Sean Smith
2020-03-04 08:37:00

Benjamin Tolputt
2020-03-04 08:39:10

Benjamin Tolputt
2020-03-04 08:43:20

Sean Smith
2020-03-04 09:06:23

Dirron De Human
2020-03-04 09:13:32

Sean Smith
2020-03-04 09:14:08

Connor Goodwolf
2020-03-04 09:15:27

Jarrod Smith
2020-03-04 09:22:33

Sean Smith
2020-03-04 09:25:53

Benjamin Tolputt
2020-03-04 09:29:30

Sean Smith
2020-03-04 09:32:31

Benjamin Tolputt
2020-03-04 09:33:32

Benjamin Tolputt
2020-03-04 09:34:12

Benjamin Tolputt
2020-03-04 09:35:45

Sean Smith
2020-03-04 09:48:00

Josh Dalgliesh
2020-03-04 09:48:45

Benjamin Tolputt
2020-03-04 09:50:58

Gregore Conn
2020-03-04 10:02:37

Amy Baldwin
2020-03-04 10:06:58

Gregore Conn
2020-03-04 10:10:47

Stephen Farrell
2020-03-04 10:25:55

Sean Smith
2020-03-04 10:42:36

Sean Smith
2020-03-04 10:43:25

Jon Mitchell
2020-03-04 10:57:08

Jon Mitchell
2020-03-04 11:02:23

Sean Smith
2020-03-04 11:06:46

Sean Smith
2020-03-04 11:08:06

Micah Vestal
2020-03-04 11:17:51

Jon Mitchell
2020-03-04 11:20:27

Jon Mitchell
2020-03-04 11:21:43

Micah Vestal
2020-03-04 11:23:01

Tim Parks
2020-03-04 11:34:06

Sean Smith
2020-03-04 11:34:15

Sean Smith
2020-03-04 11:34:55

Micah Vestal
2020-03-04 11:36:16

Max Dercum
2020-03-04 11:37:26

Zakkari Clark
2020-03-04 11:43:49

Tim Parks
2020-03-04 12:09:37

Benjamin Tolputt
2020-03-04 12:43:28

Matthew Eastman
2020-03-04 12:57:21

Jon Mitchell
2020-03-04 13:06:46

Jimmy Gent
2020-03-04 13:08:49

Matthew Eastman
2020-03-04 13:10:35

Jimmy Gent
2020-03-04 13:13:28

Jon Mitchell
2020-03-04 13:16:31

Benjamin Tolputt
2020-03-04 13:17:32

Chris Svo
2020-03-04 13:19:13

Jon Mitchell
2020-03-04 13:20:03

Benjamin Tolputt
2020-03-04 13:25:03

Tristan Jones
2020-03-04 13:25:05

Jon Mitchell
2020-03-04 13:30:59

Benjamin Tolputt
2020-03-04 13:31:55

Jon Mitchell
2020-03-04 13:33:09

Matthew Eastman
2020-03-04 13:33:24

Sean Smith
2020-03-04 13:35:57

Byron Taylor
2020-03-04 13:39:44

Jimmy Gent
2020-03-04 13:41:41

Jon Mitchell
2020-03-04 13:42:18

Sean Smith
2020-03-04 13:42:35

Alec Traynor
2020-03-04 13:44:08

Benjamin Tolputt
2020-03-04 13:44:14

Benjamin Tolputt
2020-03-04 13:45:52

Jimmy Gent
2020-03-04 13:46:13

Benjamin Tolputt
2020-03-04 13:47:49

Byron Taylor
2020-03-04 13:48:23

Sean Smith
2020-03-04 13:55:36

Smith Hayward
2020-03-04 13:58:23

Smith Hayward
2020-03-04 13:59:12

Jimmy Gent
2020-03-04 13:59:14

Jon Mitchell
2020-03-04 14:01:46

Jimmy Gent
2020-03-04 14:02:23

Jon Mitchell
2020-03-04 14:02:51

Jon Mitchell
2020-03-04 14:04:26

Jimmy Gent
2020-03-04 14:04:48

Jon Mitchell
2020-03-04 14:06:51

Jon Mitchell
2020-03-04 14:08:54

Jon Mitchell
2020-03-04 14:09:20

Smith Hayward
2020-03-04 14:09:40

Jimmy Gent
2020-03-04 14:11:07

Sean Smith
2020-03-04 14:12:20

Smith Hayward
2020-03-04 14:12:49

Jon Mitchell
2020-03-04 14:13:34

Jon Mitchell
2020-03-04 14:14:00

Smith Hayward
2020-03-04 14:14:48

Cameron Surfass
2020-03-04 14:15:20

Smith Hayward
2020-03-04 14:15:57

Sean Smith
2020-03-04 14:18:20

Jon Mitchell
2020-03-04 14:20:00

Jon Mitchell
2020-03-04 14:21:14

Jimmy Gent
2020-03-04 14:22:42

Cameron Surfass
2020-03-04 14:23:51

Smith Hayward
2020-03-04 14:31:55

Smith Hayward
2020-03-04 14:32:49

Smith Hayward
2020-03-04 14:34:14

Jon Mitchell
2020-03-04 14:34:36

Smith Hayward
2020-03-04 14:34:56

Scott Kernaghan
2020-03-04 14:36:01

Kevin Rank
2020-03-04 15:16:33

Benjamin Tolputt
2020-03-04 15:23:21

Michael Beal
2020-03-04 15:30:59

James Forder
2020-03-04 15:40:29

Benjamin Tolputt
2020-03-04 15:51:29

Michael Beal
2020-03-04 15:53:54

Krunoslav Zlomislic
2020-03-04 15:56:26

Toby Kirkby
2020-03-04 16:05:08

Alex M Cruz
2020-03-04 16:13:12

Benjamin Tolputt
2020-03-04 16:17:05

Darren Wade
2020-03-04 16:22:14

Michael Beal
2020-03-04 16:23:14

Benjamin Tolputt
2020-03-04 17:10:48

Daniela Rye Nielsen
2020-03-04 17:12:44

Benjamin Tolputt
2020-03-04 17:13:45

Joel Reid
2020-03-04 17:15:40

Benjamin Tolputt
2020-03-04 17:16:10

Benjamin Tolputt
2020-03-04 17:16:44

Nektarios G Varras
2020-03-04 19:19:18

Benjamin Tolputt
2020-03-04 19:21:08

Toby Kirkby
2020-03-04 19:22:05

Toby Kirkby
2020-03-04 19:25:55

Nektarios G Varras
2020-03-04 19:27:52

Benjamin Tolputt
2020-03-04 19:31:24

Micah Vestal
2020-03-04 21:04:15

Matt Shears
2020-03-04 23:27:39

Carlos Sisto
2020-03-05 01:56:19

Byron Taylor
2020-03-05 02:02:50

Bill Keeter
2020-03-05 02:09:54

Thor Polukoshko
2020-03-05 02:51:16

Thor Polukoshko
2020-03-05 02:52:47

原文網址 Humberto Franco Larrosa
2020-03-04 02:26:24

Hello everyone, sorry if it is not the place, what is your opinion if someone has experience with the form lab printer?

翻譯年糕

Scott Pavlich
2020-03-04 08:23:02

Humberto Franco Larrosa
2020-03-04 08:25:32

全不選發文排行