• #maker+t=market
  • 3D列印服務
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 3M

原文網址 Piotr Kuśmierski
2020-03-27 08:27:00

I thinking about printing really small objects like 2-3mm... I think what would be best setting to neglect the fact that bottom leyer is usualy flattened. Anyone had experience with printing objects so small any recomendations or tips ?

翻譯年糕

Jon Hazan
2020-03-27 08:31:10

I actually did this the other day with Stuart
You need to use supports and a raft. At that size I couldn't get something that small to stay atrached to the build plate

Niall Forrester
2020-03-27 14:37:23

I agree that supports is probably the way to go. At that size, if you are designing the parts yourself, one option might be to build supports into the model itself.

I have built cast resin model kits, and they commonly have small parts mounted on a l arger 'sprue'. You then cut off the parts with a sharp knife or razor saw. I have considered this option for my own printed small parts where supports will be tricky (not actually experimented with the idea yet though).

If using normal supports, try using only one or two smallish supports at the lowest point(s), then really tiny supports elsewhere if needed. Experiment with your own support settings, do not trust default settings (for sure avoid auto generated supports). And spend some time figuring out the orientation that will minimise the support needed.

Piotr Kuśmierski
2020-03-27 17:43:29

I think I'll have to design supports myself because those of chitubox even when added manually "bite" into the model too deep. Thank you for the advice!

Jon Hazan
2020-03-28 23:16:42

Piotr Kuśmierski Use PrusaSlicer it has far better supports. Add the supports, export and then slicer as normal in chitu

Piotr Kuśmierski
2020-03-29 02:12:39

The prusa slicer supports bite in model even deeper ;) . I use it daily on larger models


原文網址 Michael Rieser
2020-03-23 06:14:22

These are photos of the same coronadice. Since Changing the FEP earlier this week, I haven't gotten any successful prints. I've switched to this model as it's small and demonstrates the problem. I either get supports and no object on the build plate or distortions like these.

I have releveled. The problem seems related to changing the FEP. As for temperature, my house hasn't changed, but I'm sure warmer would be better for the resin.

This is a Photon S. Anycubic ECO Resin. Prusa supports at 100%. Photon Workshop slicer (latest version).

50 um lyaer thickness
5 sec normal layer
2 sec off time

30 sec bottom
6 bottom layers

5mm Z-Lift Distance
2mm Z-Lift Speed

3mm/s Z Retract Speed

Any help is appreciated!

翻譯年糕

Fred Breton
2020-03-23 06:54:03

Increase exposure by 2 sec

Michael Rieser
2020-03-23 08:03:36

Thanks!
You've prompted me to try printing this:
https://www.thingiverse.com/thing:4123340

Michael Rieser
2020-03-23 10:13:41

Michael Rieser
2020-03-23 10:13:52

I

Michael Rieser
2020-03-23 11:38:48

Fred Breton My wife and I determined #4 (6 secs) was the best. I'll retry with that tomorrow. Thanks!

Michael Rieser
2020-03-24 02:29:16

Fred Breton My Corona!
I didn't think changing the FEP (my first) would have affected my exposure settings. I believe my old FEP must have been much looser than the replacement.
Thanks again!


原文網址 John Driggers
2020-03-17 03:15:30

Zero owners - I'm struggling to get my bed leveled - it seems like no matter how gentle I am, one side twists and is a bit lower than the other. I'm able to get good prints, but I'd like to get them better.

I'm printing some better test objects - but even on this, it's off 0.3mm.

翻譯年糕

Keith O'Donnell
2020-03-17 03:17:55

Honestly, I haven’t found resin to be good for perfectly flat requirements. I mean, you really wouldn’t want to make anything mechanical with this stuff.

Diego Gonzalez del Rio
2020-03-17 03:27:23

Don't print it flat on the bed. The suction twist the "bottom layers"

Mark Wardle
2020-03-17 03:27:32

would not worry about it. printing directly of the bed is where the base of supports are and those are throw away. so alsong as the models stick and tbh the pics look fine.

Mark Wardle
2020-03-17 03:28:16

i tend to print miniatures directly of the base as the base. again the pics look great. :)

John Driggers
2020-03-17 03:30:22

I print a lot off the bed as well, and it's just bad enough that it triggers my OCD. :) I'm printing a better test object now - this is my first Anycubic, so my first go with the bed mount / leveling mechanism.

Jonathan Bollon
2020-03-17 03:31:14

Man, you're asking a 400€ printer to be as accurate as a 26 000 one. Guess what ?

Keith O'Donnell
2020-03-17 03:38:01

John Driggers I mean, I wouldn’t say it’s OCD until you’re up at 3 AM printing your 20th imperfect cube because you’re afraid your house might catch on fire if you don’t.

John Driggers
2020-03-17 03:44:47

No, I'm asking that it be as accurate as a $299 one a single axis. The $26k one I get 0.025mm out of on three. :)

David Collinson
2020-03-17 03:49:25

Ah, I see your problem. Your test equipment is too good! Use cheaper and less accurate verniers and the problems will go away ;)

David Collinson
2020-03-17 03:51:45

Also, this is a good solution. There are others out there that do the same thing, and on thingiverse if you want to make your own (metal is smarter to use then resin). Set this right, and making sure the photon itself is level to start with, and it'll eliminate that discrepancy pretty well

https://www.fepshop.com/....../anycubic-photon-easyz0-kit/

John Driggers
2020-03-17 03:58:09

That looks a lot like what I want - thanks David !

Jonathan Bollon
2020-03-17 05:25:51

John Driggers Teh you're already as accurate as you can be with a photon. Now if you want something a little better, take a better resin. The machine itself can't get better than that.

John Driggers
2020-03-17 05:27:53

David, do you know off the top of your head if the Zero and the "Normal" Photon mounting heads are the same size? I'm not at the house yet....

David Collinson
2020-03-17 06:17:05

John Driggers not off the top of my head, no.

Travis Callahan
2020-03-17 06:18:14

agreed. I recommend SPI. Or as we in the machining world like to call them Sorta precision instruments.

Caio Donini
2020-03-17 08:06:51

It's a chinese printer, use chinese gauges!

Darko Miljak
2020-03-17 17:46:47

Resins have properties FYI, shrink age and elongation. Unavoidable. Some companies clearly state those properties, some dont. The printer itself is not the issue, the resins are.

Michael D Showalter
2020-03-17 19:25:39

Try leveling your entire machine, then level the bed. Leveling the bed really only makes it flush in regards to the build plate, but if the machine isn't level, nothing will be...liquids need to be level to the world, the build plate only needs to be level in regards tot he bed

John Driggers
2020-03-17 20:59:25

David Collinson just an FYI - not the same, nor the same mechanism. I was able to carefully tune most of it out by repeatedly leveling and retightening. Gonna try and figure out what’s causing it and see if I can come up with a solution.

John Driggers
2020-03-17 21:18:23

You think it's the resin that causes one half of the print to be thicker than the other?

Juan Pablo Bagnon
2020-03-17 21:19:12

you are fighting with exposure(over/under) and bed leveling, best way to avoid those is to put 5mm supports on it.

Mike Kanellos
2020-03-17 22:05:20

I had the same problem. I kept leveling and always the same issue. After the first layer it would loose its leveling. Doesn’t matter how much I tighten the top screw! I installed the easy leveler with some adjustments and the problem is solved


原文網址 Erik Blume
2020-03-13 19:32:53

Hey there, Im new to printing with Anycubic Photon S. I tried with the tranlucent green Resin and want to change to a grey resin. I bought the one of Anycubic Resins but I hate the smell. The green resin dosnt smell, but the grey...

Could anyone give me an recommendation for a grey resin, not smelling for 28mm miniatures ? I want clear details, layerheight... 0.03mm till 0.02mm. Working settings for exposure would be a dream :)

THX

翻譯年糕

Audrey Col
2020-03-13 19:37:49

Jim Nelson
2020-03-13 19:38:02

Oliver Matthews
2020-03-13 19:42:00

Erik Morris
2020-03-13 19:42:51

Sander van Deijl
2020-03-13 20:04:25

Derek Fontes
2020-03-13 21:41:13

Aaron Strome
2020-03-14 03:34:01


原文網址 Philippe Maegerman
2020-03-04 16:29:33

Add a little bit of zen in your life ;)
60mm tall, .03mm layer height.
Resin is phrozen grey abs like.
Free model https://www.myminifactory.com/object/3d-print-113344 翻譯年糕

Daniela Rye Nielsen
2020-03-04 17:14:24

Philippe Maegerman
2020-03-04 17:37:20

Serkan Budur
2020-03-04 18:08:56

Alfons Gunnesgård
2020-03-04 21:54:54

Philippe Maegerman
2020-03-04 22:31:37

Philippe Maegerman
2020-03-04 22:37:52

Alfons Gunnesgård
2020-03-04 23:11:16

Alfons Gunnesgård
2020-03-04 23:19:34

Philippe Maegerman
2020-03-04 23:25:37

Philippe Maegerman
2020-03-04 23:31:41


原文網址 Jonathan Shih
2020-03-04 15:32:26

Hi all, I recently received my photon and I just tried to print the photon resin exposure range tester file (X3msnake) from photonsters.

Somehow it didn’t work out quite well...it didn’t form anything on my build plate...

Any tips for me to do the exposure test?
Resin used: Anycubic ECO Clear

Any help would be appreciated. Thanks!

翻譯年糕

Dustin Cole
2020-03-04 15:45:21

Jonathan Shih
2020-03-04 15:55:35

Jonathan Shih
2020-03-04 16:01:36

Jonathan Shih
2020-03-05 12:17:47

Jonathan Shih
2020-03-05 12:19:31


原文網址 Saïmone Goblet
2020-03-04 05:37:41

I have 2 issues with my late prints, i don't know exactly why. Maybe some here could help !

- First, 2 prints in a row, my raft that was almost occupying all the space on the build plate got detached a bit and warped for some milimetters. Causing part of my supports to not print properly.

- Second, but I think it's is linked to 1 : in some areas, my raft is 1mm tall and in some other, it's 3mm. So i'm wasting way too much resin for the raft.

I already releveled the bed, but I don't see any reason why it would warp and print more than it should.

Maybe my FEP is damaged or simply too old ?

翻譯年糕


原文網址 Daniel Neubacher
2020-03-03 04:26:14

Never tried to print something as big as this one, pretty much max size of the printer. The slicer says 43ml but I dont trust it... I guess it woud be better to watch the tank, wouldn't it? I actually dont even know how much I'm pouring into the tank :)

翻譯年糕

Miroslav Zajíček
2020-03-03 04:29:03

Daniel Neubacher
2020-03-03 04:29:59

Cameron Lee Johnson
2020-03-03 04:32:56

Christopher Fugate
2020-03-03 04:33:24

Daniel Neubacher
2020-03-03 04:36:46

Matt Glover
2020-03-03 04:36:49

Daniel Neubacher
2020-03-03 04:38:58

Matt Glover
2020-03-03 04:40:33

Daniel Neubacher
2020-03-03 04:42:36

Dennis Hurlburt
2020-03-03 04:45:27

Gary Houser
2020-03-03 04:48:35

Daniel Neubacher
2020-03-03 04:57:24

Eduardo Henrique
2020-03-03 05:03:11

Eduardo Henrique
2020-03-03 05:05:15

Daniel Neubacher
2020-03-03 05:06:52

Robert Mako Sharkey
2020-03-03 05:16:07

Michael Power
2020-03-03 05:22:00

Gary Houser
2020-03-03 05:31:46

Christopher Fugate
2020-03-03 05:33:48

John Matthew
2020-03-03 05:51:24

Clay Whitter
2020-03-03 06:03:27

Arthur White
2020-03-03 06:03:48

Thomas Medina
2020-03-03 10:16:48

Robert Mako Sharkey
2020-03-03 13:30:17

Arthur White
2020-03-03 15:32:48


原文網址 Mike Adrian Laxa Pring
2020-03-01 15:02:13

Hello, I need help with my photon. It seems to be pausing in itself during midprint(50-60% completion), then stops the printing when I try to resume the print. The buildplate rises halfway the z axis. It did the same thing for 3 consecutive times now on 3 different files. All settings used in the printer worked before and I have no levelling issues. My prints are usually 10hrs+ and my 3months printer has the updated firmware. Anyone else encountered this issue?

翻譯年糕

Florian Gehm
2020-03-01 19:29:37

Mike Adrian Laxa Pring
2020-03-01 19:35:15

Florian Gehm
2020-03-01 19:37:53

Mike Adrian Laxa Pring
2020-03-01 20:03:20


原文網址 Andreas Bergman
2020-03-01 00:11:42

I need some help from my fellow Europeans.

I'm looking to print the Photon air filter system by Jarrod Smith, but I'm having some trouble finding a 6001 filter.

I'm trying to source all the materials on German Amazon.de as that's where I will be buying the fan and some other accessories for the printer.

I found the 3M brand filter, but it ships from either the States or the UK which means that the postage to Sweden will be way too high.

Same with the Chinese 6001CN versions.

Are there cheaper alternatives available? Perhaps a different fitting to enable the use of cheaper or more common filters?

我需要歐洲同胞的幫助.

我想列印jarrod smith的光子空氣過濾器系統, 但我很難找到一個6001的過濾器.

我正試圖從德文Amazon.de上獲取所有材料, 因為我將在那裡為印表機購買粉絲和其他配件.

我發現了3米品牌過濾器, 但它從美國或英國發貨, 這意味著瑞典的郵資太高.

中國6001 cn版本也一樣.

是否有更便宜的替代品? 也許另一個適合使用更便宜或更常見的過濾器?

https://www.amazon.de/dp/B000XBKLLE/ref=sr_1_2?keywords=6001+filter&qid=1582992251&rnid=1703609031&s=diy&sr=1-2

· 查看原文 · 為此翻譯評分

Alex Hendry
2020-03-01 01:46:53

Andreas Bergman
2020-03-01 02:01:17

Quol-Amin Impcasor
2020-03-01 03:11:02

Andreas Bergman
2020-03-01 03:21:42

Quol-Amin Impcasor
2020-03-01 03:28:18

Tom Sargison
2020-03-01 05:51:03

Dan Hjulberg
2020-03-01 06:17:56

Andreas Bergman
2020-03-01 06:57:51


 

全不選 發文排行