ATOM 3D Printer Group 造訪社團

順便拔掉晶片看看？

這個嗎？

是不是有自己改過firmware? 先用PC 連線看看能不能讀到資料,如果可以就可能是軟件LCD type 設定問題.還有EXP1 & EXP2 有沒有對應插對位置.
另外LCD 螢幕一般只有兩條排線,你怎會有三條?

除了LCD可能壞了之外，另一個可能性是主控版的驅動有壞掉

林廷奕 今天早上用Cura 3.2.1測試加熱板、噴嘴加熱、進料功能、印製物品等，都運作正常，就是LCD無法正常顯示字元，無法進行校對作業。若調整LCD控制器的電阻，僅多出現2排發光區域。建議更換控制器RepRapDiscount smart controller 2004 lcd！

不怕斷嗎？@@

內填50%,意外地強壯！

樓主鈑金件送去烤漆，整體質感更加分

建議換方向印，固定的長柱跟底下方型座連結那邊強度比較低

是27吋嗎 跟我幾乎一樣!

是位硬漢

感覺有點危險...
然後三螢幕比二曲幕實在(無論價錢或功用)

覺得想印

是消光色耶

Q

沒有橘色用黃色取代，嘴巴印的不好，沒有辦法活動

金鵝獨立

好Q！

金古錐~

嘴巴搞定了

2個建議, 可擇一而試即可: 1, 把噴頭清乾淨, 2,把「流量」由100降為90

請問這中文切片軟體，是哪套呀？可吿知去哪下載嗎？

cura去它們官網下載就可以~

是的在官網下載的

張榮濱 謝謝

個人覺得會回彈有點詭異
塞住通常是直接刮料比較常見
嗯⋯⋯
晶片電壓有調適當嗎？

請問電壓在哪邊調整呢？

可以問這是哪個材質的線材嗎??

上網看一篇文章~~倒抽長度改成1.5mm、倒抽速度改成10mm就ok了!

PETG

如果你是印PLA的話
原本的回抽設定應該沒什麼問題
換成你說的設定可能也會讓牽絲的情況變嚴重
如果問題再發生的話就檢查看看電壓吧
只不過要要拆床，比較麻煩
https://atom3dp.squarespace.com/machine-check-tw/......

楊梓玄 感謝，等我拿到電表再來試試看，謝謝喔！

木料本來就比較難印喔

檢查一下擠料輪看看吧！ 有沒有洞對準

這是進料齒輪的聲音吧

是的

其實原廠的雙管夾是有問題的 當進料擠壓時，雙管夾具會有一個往回推上的力量，慢慢的管子就會位移，然後料就會回推冷卻，最後卡住，你只要改成跟fx型號的雙管夾就可以解決這個問題

木質料嗎?0.4噴頭不建議用木質料

木料別莢太緊！
溫度調高一點，讓線材容易軟化一些！

用220度試看看

I don't own one but looks like it can be becurse the bed is not level have you tryed a ned levering of the grid

Remove the spring when you do bed leveling, and assembled it back after bed leveling.

I didn't had this before and the bed or the glass plate can't be placed in another way. For the spring, I don't think that the spring doesn't do its work, it is as the steppers don't move in equilibrium to each other. Can the voltage change on the drivers of the steppers. I once calibrated them to 0,4V because they had a different tension each.

Please try to remove this spring first, then do the bed leveling again, this is main reason what cause atom nozzle error move, I had experienced before and it is not happened only on me, but also many atom owners, so do it and see what will it happens!

Hi Marx, why is Atom not redesign it without the spring? I should have done it in another way, because the sheet metal part on the head is being deformed by the executed pressure on the nozzle. I think that this is also the reason why the leveling is c hanging each time. It should be constant, but with this design it isn't possible. Deformation is a real fact, also the pressure isn't the same allover the bed. This point and each point next to the guides are very strong in pressure.

How wut you rate the atom martial is it worth the many money? Becurse I am consetering one becurse I am tired of problems with the real cheap printers on ebay my printer now is little monster and hate it so many problems

Hey Martial Geudin, to be honest this is old problem in Atom 2.5EX version, and I don't know why they let this exists till now, you can try searching " bed leveling " in group, it will shows tons of same issues with your situation now.
It was a good machine and good group here, but now a lot different.

Oki Marx wu soo you think ? wait to new versions?

to be honest, no machine is really good, we are dealing with a new technology, even it is 25 years old. many have tried to make something better, but still running into the same problems. You need a good industrial designer to analyze and improve this techniques. I am following this domain since the beginning, good machines are expensive and still having issues. So there is a lot potential in this market but with lots of competences. And we have to learn from what was already made to improve and build on it.

My old Atom 2 was and still is a fantastic machine! I bought 2 AtomEx2.5's and have had nothing but problems with bed levelling issues etc. Both my AtomEx 2.5's have the exact same problems including other random issues like print shifting half way th rough a large print for no apparent reason. My old custom built prusa and a couple of modded Makerbot2's also never fail me even after several years of constant use doing full volume print after print. So yes there are good machines in my experience.... But everyones mileage varies I guess.

How is support on it then? On the printers and spare parts? Thanks again

Per Andersen As Sean Thompson said, atom 2.5EX is a fantastic machine, reasonable price, I had have it from Version 2, and ungraded to 2.5EX except the bed leveling problem I had, not to much problem happened.

It was good enough but it didn't move on since version 2.5FX, it has been a while...

這是什麼模型阿？ 是自己畫的嘛？

黃俊傑 這是公司的產品，單車的迷你休息把

用束緊帶束起來

跟ping比起來，不知道效果會差多少！

ATOM+1

what resilution is it in ?

and speed