ATOM 3D Printer Group 造訪社團

降價為3000

尚未售出

請問規格 跟 能郵寄嗎？
謝謝

售出了嗎?

售出

有沒有人可以幫忙，C01跟C02結合 ，C03跟C04結合，這樣的話效果可能比較好

EASY,方法有傳給你了 廖新弘

目前進度，眼睛附近的黑色是筆塗的

請教這個字如何印出來?因為上次嘗試製作印章(約15x15mm),字的細節無法印出來,是因為列印速度太快的關係嗎?

總於有正向的文章了。

這出貨品管太糟了

讓您收到有瑕疵的零件真是不好意思，期待您的作品分享 ❤

Is it actually the bed or no?

It looks like it thinks the printing bed is larger than it actually is

I've been printing on that exact same bed configuration for over a year. All of a sudden the printer seem to lose track of where Z equals 0 is. I have no idea what the problem actually is.

Yea, no idea. I'd replace the motherboard and see what happens.

I've had the same thought. Do you have any suggestion on which MB would be a good replacement? (Good = will run with vanilla Ta At om2 firmware.)

WOW really crazy @_@

If the touch sensor can work well, u may change the printing area by using smaller diameter, like 210 or 200 to c if it can work or not.

or u just change the spring on the screw of touch sensor? maybe the spring too hard for touch sensor?

I remember at one point I was using a different board that wasn't from the Atom dudes and my prints were always just not perfect. It could have been me and my settings, but they were off. I also had to reverse some numbers in the settings to get the other board to work. At some point I bought another new Atom board and started using that. Let me look up the non-atom board

MKS BaseV1.2 3D Printer Controller Board (RAMPS 1.4 + Arduino 2560 remix board)

this was the name of the board. I bought it on Amazon from Keyes themselves but the item is no longer on Atom being sold by them.

and that was recommended by the Atom dudes as a replacement for not using their board

Hmm mm. Not exactly encouraging. I'll do some research and see what I can find.

看到真懷念剛裝好atom那時的情景

Cherub Shiao The sensor is the standard Atom2 micro-switch. It works fine ; the auto level function runs perfectly up to the place shown in the video.

Amazon has that board for $37.77 which is fine. But it has a different shape which means the mounting holes will be different, so attaching it to the Atom2 frame will not be simple.

Also it looks like the stepper drivers are soldered to the board and not plugged into connectors on the board. This means there's no way to replace a driver if one goes bad. I've saved an old/bad Atom2 board just to have some backup stepper drivers if needed.

Remove the spring during bed leveling

Dan Salvador That's an interesting suggestion that would never have occurred to me. I don't see why it would change anything, but I'll give it a try and post results here. Thanks.

I was really surprised, but removing the spring allowed AutoLevel to complete OK.

But now I have a different problem - the printer fails to remember the Z-Offset setting. Each time I set it and then do Adjust Offset the printer behaves like the offfset has not been set. I may be able to compensate for this by setting a Z-Offset value in my slicer.

Birk Binnard well known issue , during the first print after the bed leveling adjust the offset

Well it certainly wasn't well known by me! But thanks for the info.

I haven't been able to make a first print since completing the bed leveling because the printer crashes the hotend into the bed as soon as it starts to print. And I have re-adjusted the offset after this happened and it didn't fix the problem.

I'll go through the whole process again and see what happens.

Since the AutoLevel completed OK (after removing the spring from the Z-Min adjuster screw) I thought I'd try Auto Calibration to see if that helped things at all. But that function crashed the hotend into the print bed on the 4th move. So there is still something wacked with the printer.

I wish I knew what it was.

After a considerable time testing and checking I found 2 problems, one of which I was able to correct:
1. The small metal flap on the Z-Min micro switch was disconnected from the switch and stuck, by magnetic attraction, to the inside of the end effect or frame. The flap is small enough to hide inside the curve of the frame, so it was difficult to spot. But I finally did find it and after partially disassembling the hotend was able to reinstall it on the bottom of the microswitch.
After this I was able to successfully complete an Auto-Level and Z-Offset adjustment - sort of (see #2.)
2. I'm beginning to suspect some sort of internal EEPROM error because the Z-Offset value keeps getting messed up. Here's a typical scenario:
Perform Adjust Offset and set proper offset using the LCD knob
Perform Adjust Offset again to verify it is OK. It isn't.
Check Z-Offset value on LCD. It is far different from what it should be
Change Z-Offset vaue to 0.00
Perform Adjust Offset again and re-adjust to proper value
Check Z-Offset on LCD - this time it matches previous setting
Run test print with Layer Height = 0.200 mm
First layer prints ok, second layer shows 0.300 for part of the layer, then switches to 0.400, third layer shows 0.400 then switches to 0.500
Stop print and check Z-Offset; it shows 1.32 which is far off from previously set value.

All this leads me to believe I do need a new motherboard.

Birk Binnard I had an issue before where my z offset like yours would just do wild stuff. That was the first time I replaced my board. Second time I replaced it was when I had that shirt I showed you way back in messenger.

Well I'm going to try a different slicer just to ensure it really is a printer problem. I don't much like the idea of replacing the motherboard, but I've done it before so at least I know what to expect.

Well there is definitely something wrong with the way the printer handles Z values. I used a different slicer (Craftware) and had similar issues with the printer's Z height when printing.

My layer height is set to 0.200 mm, but after printing the fir st layer, layer 2 showed 0.100 mm for a while, and I could hear the nozzle tip dragging over the traces from layer 1. Before layer 2 was finished the LCD switched it's display to 0.200, but that didn't seem to make any difference with how the printer was printing.

Layer 3, which should have been at height 0.400, showed as 0.300 and had the same dragging effect as layer 2. I stopped the print soon after noticing this.

So similar results from 2 different slices printing the same part makes it pretty clear there is some sort of problem with the printer itself. I thought about a bug in a stepper motor or stepper motor driver, but if that were the case the hotend X-Y position would be off from what it should be, and it's not. Only the Z value seems to be wrong.

This suggests there is either something wrong with the firmware itself, or with the way the motherboard's firmware is processing the input GCode. So it looks like I need to find a new motherboard.

?

M503 dump setting
M501 Try to restore failsafe default
M503 dump setting again.
M500 for save setting

Thanks Clarence - I will try that. But I doubt I'll be able to make sense of the EEPROM data.

OK - I tried that series of commands. They seemed to work OK. But printer still doesn't handle Z-Offset properly. When I do Adjust Offset the printer needs an adjustment of 1.350 mm to position the hotend at the proper height. After I do this the Z-Off set reading says 3.175. Then, if I go back and do Adjust Offset and re-adjust to 1.350 the Z-Offset value says 6.10.

Of course I know that Z-Offset is limited to +/- 2.00, so there is something very strange (at least to me) going on here.

I've got the text of those M commands if you want to take the time to look at it. Can't post them here (of course - FB is such a pain) but let me know if you want to see the output. Meanwhile I've been looking at possible replacement motherboards.

How about check the belt, wheel etc. Might need to consider something loose in mechanical.

Been there/Done that. All is OK.

Even if that were the case it wouldn't explain the Z-Offset values being so strange.

It's the farest edge, consider the cable might cause sensor not work as expect at the specific place. Try to loosen some signal cable length

OK - thanks. I'll check all the stepper motor cable connections. That is something I had not thought about.

Nope - all the cable connections are OK - I checked both ends of each. I also made sure the stepper chips were all firmly set in their sockets - they were.

我倒覺得 Kisslicer 很好用捏

我詢價三次都沒有結果
完全不知道再幹嘛欸

Atom系列的列印品質一直是手上幾台印表機中最好的，當然我還沒有機會碰更高階的機種，我也只是個業餘玩家，下班印一些自己要拿來玩的東西

https://www.dropbox.com/....../ATOM%203.0_2019.fff......

參考Monoprice Delta pro user manual跟手上Atom2.0/2.5(感謝黃大丙大大)設定檔改出來，給Simplify3D用看起來還OK

https://www.dropbox.com/....../Monoprice%20Delta%20Pro......
這個是跟Simplify3D詢問，要到的Monoprice Delta pro設定檔

我是直接用 Cura 舊的配置 (2.5Ex) ，也沒什麼問題。機器有開箱即用的感覺，但是對於切片軟體，還是覺得很不直觀

有點想，但是我又有點想整個砍掉重練

砍掉也不錯~~~~

我要一組，請給我匯款帳戶

我，給我帳戶

.....你好快喔~~~

好喔~~~!!!!感謝老闆

感謝樓上二位~~~~
暫時售完~
其實這專案已經完成了一段時間...
但是看板上有人在銷售類似功能產品,
所以先讓路~這東西開發打樣階段開發到現在實用
也只是先求回本而已^ ^

因為才刷了Duet2跟新的effector

感恩！這也是很棒的設計！
好東西大家都會分享的 A_A

只是剛好看到，我需要這套件很久了.......

不鏽鋼鐵板跟模具

鎖上上模壓版跟下模下模壓版

疊上去模具~準備鎖緊

鎖後成形卸下螺絲跟彈簧

完工~~~~不鏽鋼小飛機變形完成

金剛合體~~!!!

第一組在我們家！感謝水豚兄讓我家老atom復活

不客氣~~~~延續ATOM的生命

可以了解一下嗎？

還有嗎？

https://www.youtube.com/watch?v=UZALg4KeeHI

https://www.youtube.com/watch?v=k7H7AjkVvaU&t=4s

可以再做~~~~不過目前手上料件快接加熱塊有缺~~~~先買來在說好了

好的~ 等你

https://www.youtube.com/watch?v=2f291r9DHfA

還有嗎？

陳進明 最近會做吧！應該要開個調查喔

感謝

https://forms.gle/QpAn7U1KiEk4m1317

預購連結
https://forms.gle/QpAn7U1KiEk4m1317

許阿瑋 預購連結 https://forms.gle/QpAn7U1KiEk4m1317

已匯款，感恩

請問是填單就可以訂購嗎??這樣的改變非常理想~~

H-m Lin 是的，我可以預估要做的數量，填單裡面有匯款資料喔

許阿瑋 好的，

蕭浚宇

已填

快要結單了喔~~~~~~~~
應該是不會多做^ ^"
請各位把握^^

9號才回台灣我要2組

還有嗎？

我的是Atom 2.0也可以用嗎？ 如果可以的也有貨，我要一組

看圖片好像加熱片附近有幾處滿尖銳的 :p