ATOM 3D Printer Group 造訪社團

速度降到30，測風扇先關閉，試試

最好列出這是甚麼物料, 線寬 和 線間距 設定是多少.
可以是調平沒做好, 也可能是出料不平均.
出料不平均的原因可以是溫度不夠, 也可能是線沒夾得夠緊.
也可能是平台塵多, 料貼不住平台.

請問cura 間距是要在哪設定阿

林志鎰 謝謝！

Adrian Li 謝謝 平台確實有一段時間沒有擦拭 我試試看吧溫度調整 調平再做一次

柯統海 cura 隱藏了很多進階設定, 你要先把它顯示出來, 線間距 是LINE SPACING, 不確定中文是否"線間距", 就是每條線拉出來之間多小間距, 這個設定多了, 線就疏落了, 但一般如果沒自己主動去搞過, 這個設定是按照LINE WIDTH即線寬去自動計算的...

Adrian Li 又學到一招 謝謝大神

溫度拉高試試;依我個人經驗應該是線料品質本身濃淡不一，拉高溫度讓出料順應該能改善

換一捲料試試

You should post your info on a Duet message board (if there is one) because that's what is really driving your extruder motors. You can also look at the generated GCode for T0 and T1 - those are the commands that determine which extruder motor is curr ently active. For single extruder printers the default is T0, so if you tell your slicer that you have only one extruder it may not generate any T0 commands. But with dual extruders specified there will definitely be both T0 and T1 commands in the GCode.

Also make sure you have connected your extruder motors to the correct stepper driver connectors on the motherboard. They all look alike and it's easy to get them mixed up.

PS: That light you have on the hotend looks great - what is it? And what powers it?

The light is just a 9-30v 80mm ring/halo LED, and I'm running it off of one of my PWM fan headers, so I can actually dim it and stuff.

It's extruding like it's supposed to, it just seems like it's extruding too fast. I will ask on the Duet forum.

Here is the amazon link of what I ordered: https://www.amazon.com/gp/product/B078Y6MFNB

Great info - thanks. I'm getting mine now.

Birk Binnard here is the mount I am using, and it seems to work fine. I have it zip tied on for now, going print the other one in cf+polycarbonate.

https://www.thingiverse.com/thing:2807099

Very good - thanks again. I was considering hot glue but that adapter is probably better.

I'm going to use servo tape to seat it permanently.

I printed that Thingiverse part - it doesn't seem to fit very well but it does stay on. Maybe I'll hot glue that to the carrier and then figure a way to attach the light to it.

Mine kind of snaps on, but can come off pretty easily. That’s why I was saying servo tape, but I suppose hot glue will work too.

Still no response from Atom support. Is there a regional holiday going on that I'm not aware of?

Hey John - I got my 2 ring lights today - they look great. But do you know what that rectangular black piece is for? Will the light work if I cut it off and connect the wires directly to one of the fan wires?

Here's a pic of how I'm attaching mine - I just used the sticky tape on top of the light and stuck it onto the bottom pf the printed adapter you found. The clips holding the adapter on to the bottom carrier aren't great, but seem to be able to hold on well enough.

Holy cow! That puppy is really bright. I did a temporary hookup just to see how it worked and it just about lit up the whole room. I'm tempted to cut off that rectangular thing, but I'm leery of what that might do to my motherboard. There really is no good place to put it if it has to stay.

Never mind - I found the answer. This page shows what's inside the little rectangular thing: https://www.amazon.com/....../ref=sspa_dk_detail_6...... .
So I used an X-Acto knife to pry it open and sure enough there are a couple of components in there surrounded by a piece of heat-shrink insulation. These will be small enough to not cause a problem so I'll do the installation in the morning.

Birk Binnard , dont cut that out. That is a resistor to keep the LED from burning up.

我上次私訊fb也沒反應
寄Email比較快哦
或者是直接打電話

要寄E-mail啦！
3代還沒出貨前，目前社群一片死寂～

Yu Yam Shen 您好！請直接來信 support@atom3dp.com 喔，我們都是很迅速回信的！

其實我們也想看FB官方看一點atom3跟atomx的進度，也想看看童阿 ?

進度...唉...從我收到要延遲出貨的Email後，寫Email問問題後到現在也還沒收到回覆呀！還是我寫的是比較情緒化的信所以就乾脆不回了。

阿~~~~~~~~~~~~~~ ?